Dremel Fortiflex 9100 Série Traduction De La Notice Originale page 12

Masquer les pouces Voir aussi pour Fortiflex 9100 Série:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 18
SPECIFICATIONS
GENERAL SPECIFICATIONS
Voltage Rating . . . . . . . . . 2 0-240 V, 50-60 Hz
Rated Input . . . . . . . . . . . 300 W
Rated Speed . . . . . . . . . . 22,000 rpm
Chuck Capacity . . . . . . . . 0.3 - 4.0 mm
ASSEMBLY
FIGURE 1
A. Power cord
B. Foot pedal
C. Hanging motor
D. On/Off switch
E. Hanger
F. Flexible shaft
G. Hand piece
H. Wall mounting piece
I.
Metal hook
J. Allan key
K. Key
GENERAL
1. Mount the inner shaft to the spindle of the motor.
FIGURE 2
2. Mount the outer shaft to the motor by turning it
counter-clockwise. FIGURE 3
3. Mount the hand piece on the other end of the shaft.
FIGURE 4
4. Mount the metal hook to the wall just above where
you work.
5. Connect the motor to the foot pedal. Connect the foot
pedal to the outlet. FIGURE 5
Do not connect the motor to the outlet directly.
6. Hang the motor on the hook.
CHANGING ACCESSORIES
1. Check if switch is in "0" position.
2. Use key to unlock and lock accessories in the chuck.
FIGURE 6
GETTING STARTED
USE
1. On/off switch
Switch on/off the tool by pushing knob D (FIGURE 1)
in "I"/"0" position.
2. Foot speed control
Control the speed stepless with your foot by applying
less or more pressure on the pedal. FIGURE 7
HOLDING AND GUIDING THE TOOL
Pencil grip for precision work (engraving). FIGURE 9
Hand grip for rough work (grinding). FIGURE 10
Do not bend shaft at tight angles. FIGURE 11
APPLICATION ADVICE
Tool is intended to be used for woodworking, jewellery
making, stone working and artisan projects.
When used with the appropriate accessories this tool
can be applied for grinding, sanding, cutting, engraving,
polishing, drilling.
Recommended speed
low – medium
precise drilling, polishing
medium – high
sanding, cutting, engraving
choose the right accessory and determine the optimum
working speed.
Do not apply too much pressure on the tool; let the
speed do the work for you.
MAINTENANCE
Flexible shaft needs to be lubricated regularly:
– switch off tool and remove plug from power source.
– remove hand piece.
– remove outer shaft by turning it clockwise.
FIGURE 3
– lubricate inner shaft with lubrication grease. Do not
use too much grease.
– mount outer shaft by turning it counter-clockwise.
– mount hand piece.
Excessive sparking mostly indicates worn-out carbon
brushes.
CLEANING
WARNING
TO AVOID ACCIDENTS, ALWAYS
!
DISCONNECT THE TOOL AND/OR
CHARGER FROM THE POWER SUPPLY BEFORE
CLEANING. The tool can be cleaned most effectively with
Always wear safety goggles when
cleaning tools with compressed air.
Ventilation openings and switch levers must be kept clean
and free of foreign matter. Do not attempt to clean the tool
by inserting pointed objects through an opening.
WARNING
CERTAIN CLEANING AGENTS AND
!
SOLVENTS DAMAGE PLASTIC
PARTS. Some of these are: gasoline, carbon tetrachloride,
chlorinated cleaning solvents, ammonia and household
SERVICE AND WARRANTY
WARNING
NO USER SERVICEABLE PARTS
!
INSIDE. PREVENTIVE MAINTENANCE
PERFORMED BY UNAUTHORIZED PERSONNEL MAY
RESULT IN INCORRECT CONNECTION OF INTERNAL
WIRING AND COMPONENTS WHICH COULD CAUSE
SERIOUS HAZARD. We recommend that all tool service be
This DREMEL product is guaranteed in accordance with
normal wear and tear, overload or improper handling are
excluded from the warranty.
In case of a complaint, send the undismantled tool or
charger and proof of purchase to your dealer.
12

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Fortiflex 9100-21 cFortiflex 9100-21

Table des Matières