Kicker ZX.2 Série Manuel D'utilisation page 2

TwoChannelModels:
Congratulations on your
KICKER purchase
Please record your purchase
information and keep your sales
receipt for validation of warranty.
Installation . . . as easy as 1, 2, 3
1. Mounting Choose a structurally sound location to mount your Kicker amplifier. The controls on the
top of the amplifier need to be accessible for adjustment. Make sure there are no items behind the area
where the screws will be driven. Choose a location that allows at least 4" (10cm) of open ventilation for
the amplifier. If possible, mount the amplifier in the climate-controlled passenger compartment. Drill four
holes using a 7/64" (3mm) bit and use the supplied #8 screws to mount the amplifier.
2. Wiring Disconnect the vehicle's battery to avoid an electrical short. Then connect the ground wire
to the amplifier. Make the ground wire short, 24" (60cm) or less, and connect it to a paint-and
corrosion-free solid-metal area of the vehicle's chassis. Adding an additional ground wire between the
battery's negative post and the vehicle chassis of this same gauge (or larger) is recommended.
Use a twisted pair of RCA (low-level) interconnect cable to feed the audio signal to the amplifier.
Only use speaker wire (high-level) inputs if
your source unit does not have RCA type
outputs. Either input method will provide a
low-level output signal at the RCA output,
which effectively passes the audio signal
to another amplifier or component
(P.A.S.T.). Keep the RCA cable away from
factory wiring harnesses and other power
wiring. If you need to cross this wiring,
cross it at a 90 degree angle.
Install a fuse within 18" (45cm) of the
battery and in-line with the power cable
connected to your amplifier. If you ever
need to remove the amplifier from the
vehicle after it has been installed, the ground wire should be the last wire disconnected from the
amplifier--just the opposite as when you installed it. See the chart below for power and ground wire
size, and fusing recommendations.
3. Configuration The following
diagrams show the most common
configurations for your Kicker ZX series
amplifier.
Two Channel Operation (Stereo) These ZX amplifiers are capable of operating into a minimum
impedance of 2 ohms per channel in stereo operation. See Figure 2.
Bridged Operation (Mono) ZX.2 series amplifiers are capable of operating into a minimum
impedance of 4 ohms when in bridged operation. See Figure 3.
Stereo and Mono Operation Simultaneously (SAMS) The ZX.2 series amplifiers are capable of
operating into a minimum impedance of 4 ohms mono and 2 ohms per channel in stereo
simultaneously with the use of passive crossovers. See Figure 4.
2
ZX.2SeriesAmplifier
Owner'sManual
ZX350.2 / ZX450.2 / ZX550.2 / ZX850.2
__________________________
Authorized Kicker Dealer:
__________________________
Purchase Date:
__________________________
Amplifier Model Number:
__________________________
Amplifier Serial Number:
Use only one type of signal input to the amplifier,
either RCA Cable or Speaker Wire
Speaker Wire
(High-Level
killers trk7"on Top"
Output) SOURCE UNIT
RCA Cable
(Low-Level)
Input
L R L
HI-LEVEL
INPUT
+ - - +
INPUT
L+ L-
REMOTE BASS
Remote Bass
Control Output
Left +
Speaker Wire Left -
(High-Level Input) Right -
Right +
ModelZX350.2 Fuse50A PowerGroundWire 8GA
ModelZX450.2 Fuse60A PowerGroundWire 4GA
ModelZX550.2 Fuse70A PowerGroundWire 4GA
ModelZX850.2 Fuse120A PowerGroundWire 2GA
ZX.2AMPLIFIER
Battery
Remote
Figure 1
Turn-On
(45cm)
Signal Out
(P.A.S.T.)
Or Less
RCA Cable
(Low-Level)
+12V
Output
Battery
R
OFF HI LO
XOVER
OUTPUT
R+ R-
Crossover
Switch
Ground
Remote
Turn-On
(45cm)
18"
Or Less
+12V
Battery
Note: To get the best performance from your new Kicker Amplifier, we recommend using genuine Kicker Accessories and Wiring.
Note: All specifications and performance figures are subject to change. Please visit the www.kicker.com for the most current information.
Minimum impedance of 2 ohms per channel in stereo operation
(60cm)
24"
Or Less
Ground
Remote
Turn-On
(45cm)
18"
Or Less
+12V
Fuse
Minimum impedance of 4 ohms when in bridged operation
(60cm)
24"
Or Less
Ground
18"
Fuse
Minimum impedance of 4 ohms mono and 2 ohms per channel in
stereo simultaneously with the use of passive crossovers
(60cm)
24"
Or Less
Fuse
Figure 2
Right Speaker
_
R-
+
R+
Signal Out (P.A.S.T.)
Signal In
L-
_
L+
+
Left Speaker
Figure 3
Mono
R- Speaker
_
R+
Signal Out (P.A.S.T.)
+
Signal In
L-
L+
Figure 4
Right Speaker
_
_
HIGH PASS
R-
+
CROSSOVER
R+
Signal Out (P.A.S.T.)
Mono
Speaker
Signal In
L-
_ +
L+
HIGH PASS
+
CROSSOVER
LOW
PASS
CROSS-
OVER
Left Speaker
3