Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
14. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
15. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving
parts.
16. If devices are provided for the connection of
dust
extraction
ensure these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
Power tool use and care
17. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
18. Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
19. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
20. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
Ampere Rating
More Than
0
6
10
12
000173
SPECIFIC SAFETY RULES
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to cutter safety rules. If you use this tool unsafely or
incorrectly, you can suffer serious personal injury.
1.
DANGER! Keep hands away from cutting area
and wheel. Keep your second hand on
auxiliary handle or motor housing. If both
and
collection
facilities,
Table 1: Minimum gage for cord
Not More Than
6
10
12
16
USB073-1
21. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool's operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
22. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
23. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
Service
24. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
25. Follow
changing accessories.
26. Keep handles dry, clean and free from oil and
grease.
USE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. When using an
extension cord, be sure to use one heavy enough to
carry the current your product will draw. An undersized
cord will cause a drop in line voltage resulting in loss of
power and overheating. Table 1 shows the correct size to
use depending on cord length and nameplate ampere
rating. If in doubt, use the next heavier gage. The smaller
the gage number, the heavier the cord.
Volts
Total length of cord in feet
120 V
25 ft.
18
18
16
14
hands are holding the tool, they cannot be cut by
the wheel.
2.
Keep your body positioned to either side of
the wheel, but not in line with the wheel.
KICKBACK could cause the tool to jump
backwards.
Prevention of Kickback")
3.
Do not reach underneath the work. Do not
attempt to remove cut material when wheel is
moving.
3
instruction
for
lubricating
50 ft.
100 ft.
AWG
16
16
16
14
16
14
12
Not Recommended
(See
"Causes
and
150 ft.
14
12
12
and
Operator
Publicité
Table des Matières
