Otto Office OS5 Mode D'emploi page 6

5 Operation
Warning!
Before switching the machine on, make sure that
you observe all safety instructions.
Switching the paper shredder on
• Set the sliding switch for automatic opera-
tion to "ON/AUTO".
ON/AUTO FWD REV
Feed paper
• Feed in the paper to be shredded, however,
never feed in more than 5 sheets at a time.
 The cutting device starts automatically,
pulls in the paper and shreds it.
When the feed opening is clear of paper
again, the cutting device switches off.
• The cutting device runs constantly if you set
the sliding switch to "FWD".
ON/AUTO FWD REV
6 Troubleshooting
Paper jam
You have fed in too much paper.
• Set the slider switch to "REV".
 Pa per is pus hed out.
• Se pa ra te pa per stack
ON/AUTO FWD REV
• Set the slider switch to "ON" again.
• Feed in pa per successively.
ON/AUTO FWD REV
Shredded material container full
NOTICE! Check the level in the shredded material con-
tainer and empty it in good time, as otherwise
the function of the cutting device could be
impaired.
• Pull out the power plug
• Move cutting head away.
• Empty cut material container.
• Remove cutting head.
For all other malfunctions, check whether the cutting head was
correctly positioned on the shredded material container before
contacting our customer service. If the motor was overloaded,
let the shredder cool down for 30 minutes before using it again.
6
7 Cleaning
WARNING
Dangerous mains voltage!
Switch off the shredder and pull out the mains
plug.
When cleaning only use a soft cloth and a mild soap-water solu-
tion. However, no water must enter the equipment.
8 Disposal / Recycling
Electronic devices must not be disposed of with the
household rubbish. Please ask your local authorities
for collection points for electronic waste where you
can deposit old devices for environmentally-respon-
sible treatment and recycling.
9 Technical Data
Cutting type
Shred size
Sa fe ty ra ting DIN 32757 – 1
Cutting ca pa ci ty DIN A4, 80 g/m
Lo ading width
Cutting speed
Voltage
Operating mode
Max. operating time
Dimensions W x D x H
Weight
Volume of shredded material container 2.9 gal (11 l)
EC declaration of conformity
Machinery directive 2006 / 42 / EC
EMC directive 2004 / 108 / EC
Low voltage directive 2006 / 95 / EEC
HSM GmbH + Co. KG, Austrasse 1 - 9, D-88699 Frickingen
hereby declares that the document shredder OTTO Offi ce OS5
complies with the EC directives listed above, including all modi-
fi cations that apply.
Applied standards and technical specifi cations:
• EN 55014-1:2006
• EN 61000-3-2:2006
• EN 60950-1:2006
Frickingen, 01.04.2009
Josef Käppeler - Technical Director Kä ä ä ä ä ä ä ä ä ä ä ä ä ä ä ä ä ä ä pp p p p p pp p p p pp p p p pp p p p p p p p p
This explanation only refers to the state of the machine when it was fi rst
put into use. Subsequent modifi cations are not taken into account.
Strip cut
1/4" (7 mm)
1
5 sheets
2
8 1/2" (216 mm)
19.5 ft/min (99 mm/s)
220 - 240 V / 50 Hz
Brief operation
2 min
11 11/16" x 6 7/16" x 14"
(297 x 163 x 354 mm)
4 lbs. (1.7 kg)
• EN 55014-2/ A1:2001
• EN 61000-3-3/A2:2005
eler r r r r r r r r r r r - T T T T T T T T T T T T T T T T T T T T echni
0911