Technical Data - VOLTCRAFT PSO-120 Mode D'emploi

UNPACKING
Check all the parts for completeness and damage after unpacking.
Damaged parts must not be used for safety reasons. In case of any damage
contact our customer service.
INSTALLING THE MEASUREMENT PROGRAM
Installing the PC software
Switch on your computer and insert the enclosed software CD into the CD drive of your
computer. The automatic start mode will automatically start the installation of the measure-
ment program. If the program does not start automatically, open the file "setup.exe" in the CD
directory.
MAKING MEASUREMENTS
The driver is installed with the first connection of the PSO to the PC.
If the installation does not take place automatically, perform it manually. To this end, go to
"Control Panel" and open the "Device Manager. Right-click the icon with the yellow exclama-
tion mark and then click "Update driver software". You can now search for the drivers manu-
ally or automatically.
To start the measurement, click on the software icon.
The measuring signal should only be applied to the internal conductor. The
external conductor (reference earth) is connected to the earth potential (pro-
tective earth conductor)
Check the measuring device and its measuring leads for any damage before each measure-
ment. Never take any measurements if the protecting insulation is defective (torn, missing, etc.).
• To eliminate the risks of electric shock, do not directly or indirectly touch the connections/
measuring points during measurements.
• Never touch the probes outside of the marked handling area during a measurement. There
is danger of a life-threatening electric shock.
• Do not use the device shortly before or after a thunderstorm (lightning! / high-power
surges!). Make sure that your hands, shoes, clothing, the floor, the measuring device and/or
measuring lines, circuits and circuit components are always dry.
CLEANING
Before cleaning the device, switch it off and disconnect the USB cable from the PC.
Live components may be exposed if the covers are opened or parts are
removed, unless this can be done without tools.
Prior to cleaning or repairing of the device, all cables have to be detached and
the device has to be turned off.
• Do not use scouring, chemical or aggressive cleaning agents such as benzene, alcohol or
similar chemicals. These might attack the surface of the device. Furthermore, the fumes are
explosive and hazardous to your health. Moreover, you should not use sharp-edged tools,
screwdrivers or metal brushes or the like for cleaning
• For cleaning the device or the display and the measuring cables, use a clean, slightly damp,
fuzz-free, antistatic cloth.
DISPOSAL
Electronic devices are recyclable material and do not belong in the household
waste.
Please dispose of the product, when it is no longer of use, according to the current
statutory requirements.

TECHNICAL DATA

Measurement inputs .............................1 channel CH1
Band width ............................................20 MHz
Input impedance ...................................1 MOhm
Bandwidth .............................................35 V/DC or 35 Vp/AC
Input impedance ...................................1 MOhm
DC accuracy .........................................±3%
Input coupling .......................................DC-AC-GND
Vertical deflection .................................20 mV/div -20 V/div
Time base .............................................1 ns to 5000 S /div
Sampling rate .......................................96 MSa/s
Memory depth .......................................8 Bit/channel
Trigger mode ........................................auto, normal, single
Interface ................................................USB2.0
Power supply .......................................5 V/500 mA via USB port
Operating temperature .........................0 °C to +40 °C,
Storage temperature .............................-20 °C to +60 °C
Rel. humidity .........................................15% to 80%, not condensing
Weight ..................................................approx. 150 g (without accessories)
Dimensions (L x W x H) ........................approx. 230 x 43 x 27 mm
System requirements
Windows -based computer, min. 1 GHz Pentium
®
graphics resolution 800 x 600, CD-ROM, USB2.0, 500 MB available disc space, Windows
XP/VISTA /7/8.x /10.
A tablet with Windows 10 can also be used.
®
G Legal notice
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© Copyright 2016 by Conrad Electronic SE.
or compatible with min. 256 MB RAM,
®
®