Whirlpool WDT750SAHZ ECO Mode D'emploi page 5

Delay displays how many hours before the cycle
will begin.
To delay the start:
1. Select a wash cycle and options.
2. Press DELAY. Each time you press Delay, it will
display the next available delay time.
3. Press START to begin the delay countdown.
(varies by
NOTE: If the door is opened, such as to add a
model)
dish, the Start button must be pressed to resume
the delay countdown.
Raises the main wash temperature to improve
cleaning for loads containing tough, baked-on food.
Dries dishes with heat. This option, with the use
of rinse aid, will provide the best drying results.
Plastic items are less likely to deform when loaded
in the top rack. Use Heat Dry for optimum drying
performance. For air dry, both Heat Dry and
Extended Dry LEDs are off.
Uses heat and additional time to dry dishes. For
the very best drying performance, use rinse aid
and the Extended Dry option.
Sanitizes dishes and glassware in accordance
with NSF International NSF/ANSI Standard 184
for Residential Dishwashers. Certified residential
dishwashers are not intended for licensed food
establishments. Only sanitizing cycles have been
designed to meet the requirements of the NSF/
ANSI 184 performance standard for soil removal
and for sanitization efficacy. There is no intention,
either directly or indirectly, that all cycles on a
NSF/ANSI 184 certified dishwasher meet the NSF/
ANSI 184 performance standard for soil removal
and for sanitization efficacy.
The Sani Rinse indicator glows at the end of the
cycle if the Sani Rinse option was successfully
completed. If the indicator does not activate, it is
probably due to the cycle being interrupted.
Use the Control Lock option to avoid unintended use of dishwasher between cycles, or cycle and option changes during a cycle.
To turn on Control Lock, press and hold CONTROL LOCK for 3 seconds. Control Lock light will stay on for a short time,
indicating that it is activated. When the Lock indicator is lit, all buttons are disabled. If you press any button while your
dishwasher is locked, the light flashes 3 times. The dishwasher door can still be opened/closed while the controls are locked.
To turn off Control Lock, press and hold CONTROL LOCK for 3 seconds. Control Lock light turns off.
Control Purpose
Press to start or resume
a wash cycle.
Press to cancel
wash cycle.
To follow progress of
your dishwasher cycle.
OPTIONS
If the door is opened during a cycle or the power is interrupted, the Start/Resume button LED
flashes. Cycle will not resume until Start is pressed and door is closed. Push door firmly closed
within 4 seconds of pressing Start.
Close the door firmly. Press and hold CANCEL-DRAIN for 3 seconds. The dishwasher starts a
2-minute drain (if needed). Let dishwasher drain completely.
The indicator LED on the front right corner of the door panel glows white when a cycle is finished.
If you select the Sani Rinse option, when the cycle is finished, the Sanitized indicator on the control
panel glows. If your dishwasher did not properly sanitize your dishes, the Sanitized indicator flashes
at the end of the cycle. This can happen if the cycle is interrupted or if water could not be heated to
required temperature. The light goes off when you open and close door or press CANCEL.
CAN BE WHAT IT DOES
SELECTED
WITH
Available Delays start of a
with any cycle up to 24 hours
cycle (on some models).
Sensor Raises the main
Heavy wash temperate
Normal to135°F (57°C).
Soak &
Clean
Sensor Uses a heating
Heavy element to speed
Normal drying times. Heat
1-Hour
Dry option defaults to
Wash
On when any cycle is
Soak &
selected, except for
Clean
1-Hour Wash.
Sensor
Heavy
Normal
1-Hour
Wash
Soak &
Clean
Sensor Raises the main
Heavy wash temperate
Normal to135°F (57°C)
and the final rinse
temperature to
(156°F (69°C).
Comments
5
ADDED TIME ADDED WATER
TO CYCLE GALLONS
(LITERS)
0:05 to 0:13 0 – 3.9
(0 – 14.6)
0:05 to 1:06 0 – 3.9
(0 – 14.6)