Gorenje DFA9535X Mode D'emploi page 10

USER MANUAL
EN
WARNING
! Always switch off the electricity supply before carrying
out any cleaning or servicing operations on the ap-
pliance.
! Avoid using materials which could cause spurts of
flame (flambées) near the appliance.
! When frying, take particular care to prevent oil and
grease from catching fire. Already used oil is espe-
cially dangerous in this respect. Do not use uncove-
red electric grates.
! To avoid possible risks of fire always comply with
the indicated instructions when cleaning anti-grease
filters and when removing grease deposits from the
appliance.
! This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety. Children should
be supervised to ensure that they do not play with the
appliance.
! Caution: accessible parts may become hot when
used with cooking appliances.
! This kitchen hood is intended for installation in dome-
stic kitchens above cooktops, cooking devices and
similar kitchen equipment.
cONTROLS
P1 P2
P1: Filter alarm reset
P2: LED on/off - holding the button down you can
change the LED intensity to High or Low
Note: LED activation is displayed by P2 only when
the lift panel is completely open.
P3: Motor on/off - 1st speed
P4: 2nd speed
P5: 3rd speed
P6: 4th speed
P7: Lift panel up/down (during opening the panel can
be stopped at the desired height by pressing the
button a second time).
5' Timer function:
Holding the buttons P3, P4, P5 or P6 pressed down
(>2") the 5' Timer function is activated. When the time
has run out, the motor turns off and the lift closes. The
LEDs change from High to Low intensity. When the
function is active, the LED corresponding to the current
motor speed blinks.
Filter alarm display:
Grease filters: After 30h of motor operation, the LED of
10
P3 P4 P5 P6
the P1 button comes on for 30'' every time the motor
turns off.
Charcoal filter: After 120h of motor operation, the LED
of the P1 button blinks for 30'' every time the motor
turns off.
cONTROLS
P1
P1: Filter alarm reset
P2: Motor on/off - 1st speed
P3: 2nd speed
P4: 3rd speed
P5: 4th speed
P6: Lift panel up/down (during opening the panel can
be stopped at the desired height by pressing the
button a second time).
5' Timer function:
Holding the buttons P2, P3, P4 or P5 pressed down
(>2") the 5' Timer function is activated. When the time
has run out, the motor turns off and the lift closes. The
LEDs change from High to Low intensity. When the
function is active, the LED corresponding to the current
motor speed blinks.
Filter alarm display:
Grease filters: After 30h of motor operation, the LED of
the P1 button comes on for 30'' every time the motor
turns off.
Charcoal filter: After 120h of motor operation, the LED
of the P1 button blinks for 30'' every time the motor
P7
turns off.
cONTROLS
P1
L1
P1: Motor on/off - 1st speed
P2: 2nd speed
P3: 3rd speed
P4: 4th speed
P5: Lift panel up/down (during opening the panel can
be stopped at the desired height by pressing the
button a second time).
5' Timer function:
When the motor is on, holding the keys P1-P4 pressed
down (depending on the speed set), the 5' timer fun-
ction is activated. When this function is active, the LED
corresponding to the speed (L1-L4) blinks. When the
5' have elapsed, the motor turns off and the carriage
closes.
P2 P3 P4 P5
P2 P3 P4
L2 L3 L4
P6
P5
L5