Varma Tec VARMA 400/2 IPX5 Mode D'emploi page 7

•Switch off the appliance at the main switch: a) if the appliance does not function correctly; b) before cleaning the outside of the
appliance, c) if the appliance is not to be used for long periods of time.
• Do not cover or block the appliance during use.
• In order to avoid creating a fire hazard, the appliance must never be installed with the radiating elements close to or facing towards curtains,
beds or other objects or materials that are liable to burn easily; always ensure that these objects are at a suitable minimum distance, to
avoid any risk of fire or heat damage.
• Never use the appliance in combination with programming devices, timers or other devices that will switch it on and off automatically.
1.MODELS
cod.V400/2-30X5 horizontal model – 3000 watt IPX5
cod.V400/2-40X5 horizontal model – 4000 watt
IPX5 cod.V400/2V-30X5 vertical model – 3000
watt IPX5 cod.V400/2V-40X5 vertical model –
4000 watt IPX5
Revolving .model for wall or ceiling installation
⚫
Without glass
⚫
Colours white RAL 1013 or micaceous iron
⚫
Power: 3000 Watt or 4000 Watt 220-240V 50/60 Hz - Class I
⚫
Heated area 28/30 square meters approx.
⚫
IPX5 protection rating - Totally protected against rain and water sprays (Star Progetti Patent)
⚫
Accessories included: 2 cables 1.5 m, wall stand bracket, the bulbs can be switched on separately
⚫
Installation Height: 3.00 m / 4,0 m
⚫
Ideal positioning: wall 45° or ceiling 45°
⚫
Dimensions horizontal model 80x22x13 cm – Gross Weight 6,5 kg Net Weight 5 kg.
⚫
Dimensions vertical model 40x13x35 cm – Gross Weight 5,5 Net Weight 4,5 kg.
⚫
2. INSTALLATION
Install the heater on wall at a distance of 32 cm minimum from the ceiling and 100 cm from the side walls. (see drawing 1 page 14). The
installation height ranges from to 3,0 m to 4,0 m maximum. The ideal installation is on wall with a 45° inclination and with the heater placed in
a perfect horizontal way. Varma 400 can also be installed hanging from the ceiling according to the instructions at page 14 drawing 2. Do not
place the heater immediately under a power socket.
3.POSITIONING
Adjust the Varma 400 reflector in the direction of the required heating bundle, when installing on a wall. It is usually a 45° inclination related to
the horizontal line. The appliance must never be installed on a flammable surface Varma 400 must be placed at a safe distance (clear space)
of minimum 2.0
m. from combustible materials such as: cartons, fabrics, curtains etc. as well as glass walls. If placed in workshops and garages where there
are flammable paints and liquids, Varma 400 must be placed at a minimum distance of 4 m from the source of danger. We suggest not to use
Varma 400 in particularly dusty and closed areas. This could damage the bulb. and turn it on and off must not be within reach of the shower
or bath.
4. MAINTENANCE
The cover and bulb must be kept clean to maintain the heater's original heat efficiency. Use only denatured alcohol and a clean cloth. Other
products may damage the heater.
5.INSTRUCTIONS FOR REPLACING THE BULB
WARNING - The Varma 400 guarantee does not cover replacement or repair of the bulb. To change the bulb
contact a professionally qualified electrician or assistance service.To change the bulb, follow the instructions
given below in the order indicated.
1.Loosen the screws that fix the rim
2.Remove the two end sides and the cover from the body
3.Remove the bulb from the supports/spring
4.Slide the two silicon washers backwards along the wire for two/three centimetres
5.Extract the two female fastons connected to the male fastons of the bulb or loosen the small screws of the clamp that
connect the bulb pins and the wire.
6.Insert the new bulb in the female fastons and fit the silicone washers back onto the two end sides or insert the pin of the new bulb and
the wire in the clamp; tighten the two small screws. Refit the silicone washers so that they cover the connections.
7.Replace the cover and the two end sides as they were originally assembled.
8.Replace the rim and tighten it.
If necessary contact our technical office phone +39/02/90639261
THE MANUFACTURER SHALL NOT BE LIABLE IN THE EVENT OF NON
OBSERVANCE OF THE ABOVE INSTRUCTIONS
7