Safety Instructions - IKRA HEM 1000 Manuel D'utilisation

d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
e) Do not overreach. Keep proper footing and bal-
ance at all times. This enables better control of the
power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection acilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the rate
for which it was designed.
b) Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
c) Disconnect the plug from the power source and/
or the battery pack from the power tool before
making any adjustments, changing accesso-
ries, or storing power tools. Such preventive
safety measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool's operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.

Safety instructions

Attention: Noise protection ! Please observe
the local regulations when operating your de-
vice.
Before operation
• The tool must be assembled correctly before use.
• The tool should be checked carefully before use. You
should only work with a tool that is in good condition.
If you notice any defect on the tool that may cause a
hazard to the operator, do not operate the tool until
such defects have been rectified.
• Replace worn or damaged parts for reasons of safety.
Use only original spare parts. Parts not produced by
the original manufacturer may have a poor fit and
possibly cause injury.
• Before use, all foreign bodies must be removed from
the working area, also pay attention to foreign bodies
during operation.
• Only work in daylight or sufficiently good artificial light.
• Wear eye protection and face or dust mask if operating
in dusty conditions.
• Dress properly. When operating the tool, pay attention
to the following notes concerning your working
clothes:
- The use of protective gloves and rugged footwear
is recommended.
- Wear a proper hat or other headgear to contain
long hair.
- Avoid wearing loose clothing or jewellery that might
get caught in the rotating tines.
Proper use
The user is responsible for third parties while
working with the tool.
• People not acquainted with the operating instructions,
children, juveniles who have not yet reached the
minimum age for using this tool, and people under
the influence of alcohol, drugs or medication are not
allowed to use the tool.
• Only use the tool for its intended purposes.
• Keep children and pets away. All onlookers should
be kept at a safe distance from the tool when it is
operated.
• Make sure that all protective devices are fitted and in
good condition.
• Do not operate the tool near underground electric
cables, telephone lines, pipes or hoses.
• Before inserting the plug in the mains socket,
make sure that the socket ratings are correct and
correspond to those indicated on the rating label on
instructions,
the tool.
• The use of the tool is only permitted if the safety
distance provided by the guide bar is complied with.
• Do not operate the tool on a slope that is too steep for
safe operation. When working on slopes, slow down
your working speed and make sure you have good
footing.
• Before starting the tool, make sure that the tines are
not touching any foreign objects and are completely
free to move.
• Grip guide bar firmly with both hands. Never operate
the tool with only one hand.
• Be aware that the tool may unexpectedly bounce
upward or jump forward if the tines should strike
extremely hard, packed soil, frozen ground, or buried
obstacles such as large stones, roots or stumps.
GB-2