Electrical Safety - Silverline 387825 Mode D'emploi

387825
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will reduce risk of electric
shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords increase the risk of electric
shock.
e) When operating a power tool outdoors, use an extension cord suitable
for outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
f) If operating a power tool in a damp location is unavoidable, use a
residual current device (RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired
or under the influence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection.
Protective equipment such as dust mask, non-skid safety shoes, hard hat,
or hearing protection used for appropriate conditions will reduce personal
injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position
before connecting to power source and/or battery pack, picking up or
carrying the tool. Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result
in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used. Use
of dust collection can reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source and/or the battery pack
from the power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate
the power tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the
power tool's operation. If damaged, have the power tool repaired before
use. Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with
these instructions, taking into account the working conditions and the
work to be performed. Use of the power tool for operations different from
those intended could result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power
tool is maintained.
Spray Gun Safety
• Never point a spray gun towards yourself, other people or animals
• Always read paint or stain manufacturer's guidance thoroughly. If paint or stain
comes into contact with skin, consult manufacturer's guidance immediately
• This spray gun works at very high pressure and is capable of penetrating skin. If
paint or stain is injected under a person's skin, seek medical help immediately
• Never use this spray gun with flammable, corrosive, toxic or abrasive liquids
• Always spray in a well-ventilated area, away from any sources of ignition. Be
aware that even very light wind will cause the paint or stain mist to drift
• Ensure other people, especially children, are kept well away from the work area
• WARNING: Solvents and paints are harmful and can even be toxic. Some
solvents and paints are extremely flammable. Handle with care, according
to the manufacturer's recommendations. Store solvents and paint in sealed,
leak-proof containers made of a material that is chemically resistant to the
specific solvent. Always wear suitable protective equipment and dispose of
solvents and paints, as well as contaminated items, as special waste, according
to laws and regulations.
• WARNING: When spraying coating materials, dangerous vapours or aerosols,
which are detrimental to your health, are produced. Please read all labels
and safety instructions carefully, and observe all indicated instructions and
recommendations. In case of doubt, please ask the material supplier. Use
respiratory protection when spraying. The respiratory equipment used must
be suitable for the material in use and adapted to the degree of the vapour
concentration. When spraying paint, use respiratory equipment independent of
the ambient atmosphere, or equipment with filter combination A1/A2-P2. Ensure
a sufficient protection of your skin during all spraying and cleaning procedures.
Wear appropriate protective clothes and use suitable protective skin ointments.
• WARNING: DO NOT spray acids, caustic solutions, removers and similar
substances.
www.silverlinetools.com
110W Spray Gun
7