General Safety - Silverline 372673 Mode D'emploi

372673

General Safety

a) For multiple hazards, read and understand the safety instructions before
installing, operating, repairing, maintaining, changing accessories on, or
working near this tool. Failure to do so can result in serious bodily injury
b) Only qualified and trained operators should install, adjust, or use this
tool
c) Do not modify this tool. Modifications can reduce the effectiveness of
safety measures and increase the risks to the operator
d) Do not discard the safety instructions; give them to the operator
e) Do not use this tool if it has been damaged
f) Tools shall be inspected periodically to verify that the ratings and
markings required by this part of ISO 11148 are legibly marked on
the tool. The employer/user should contact the manufacturer to obtain
replacement marking labels when necessary
WARNING: This appliance is not intended for use by persons (including
children) with reduced, physical or mental capabilities or lack of experience
or knowledge unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Children must be supervised to ensure that they do not play with the
appliance.
Projectile Hazards
a) Be aware that failure of the workpiece or accessories, or even of the
inserted tool itself, can generate high-velocity projectiles
b) Always wear impact-resistant eye protection during operation of this
tool. The grade of protection required should be assessed for each use
c) For overhead work, wear a safety helmet
d) The risks to others should also be assessed at this time
e) Ensure that the workpiece is securely fixed
Entanglement Hazards
a) Choking, scalping and/or lacerations can occur if loose clothing,
personal jewellery, neck wear, hair or gloves are not kept away from the
tool and its accessories
Operating Hazards
a) Use of the tool can expose the operator's hands to hazards, including
cuts, abrasions and heat
b) Wear suitable gloves to protect hands
c) Operators and maintenance personnel should be physically able to
handle the bulk, weight and power of the tool
d) Hold the tool correctly; be ready to counteract normal or sudden
movements and have both hands available
e) Maintain a balanced body position and secure footing
f) Release the start-and-stop device in the case of an interruption of the
energy supply
g) Use only lubricants recommended by the manufacturer
h) Personal protective safety glasses should be used; suitable gloves and
protective clothing are recommended
i) Avoid direct contact with moving parts in order to prevent pinching or
cutting of hands or other body parts
j) Wear suitable gloves to protect hands
k) There is a risk of electrostatic discharge if used on plastic and other
non-conductive materials
Repetitive Motions Hazards
a) When using this tool to perform work-related activities, the operator can
experience discomfort in the hands, arms, shoulders, neck or other
parts of the body
b) While using this tool, the operator should adopt a comfortable posture
whilst maintaining secure footing and avoiding awkward or off-balance
postures. The operator should change posture during extended tasks;
this can help avoid discomfort and fatigue
c) If the operator experiences symptoms such as persistent or recurring
discomfort, pain, throbbing, aching, tingling, numbness, burning
sensations or stiffness, these warning signs should not be ignored.
The operator should inform the employer and consult a qualified health
professional
6pce Recirculating Sandblasting Kit
Accessory Hazards
a) Disconnect the tool from the energy supply before fitting or changing
the inserted tool or accessory
b) Avoid direct contact with the inserted tool during and after use, as it can
be hot or sharp
c) Use only sizes and types of accessories and consumables that are
recommended by the manufacturer of this tool; do not use other types
or sizes of accessories or consumables
Workplace Hazards
a) Slips, trips and falls are major causes of workplace injury. Be aware of
slippery surfaces caused by use of the tool and also of trip hazards
caused by the air line or hydraulic hose
b) This tool is not intended for use in potentially explosive atmospheres
and is not insulated against contact with electric power
Dust and Fume Hazards
a) Dust and fumes generated when using this tool can cause ill health
(for example cancer, birth defects, asthma and/or dermatitis); risk
assessment and implementation of appropriate controls for these
hazards are essential
b) Risk assessment should include dust created by the use of the tool and
the potential for disturbing existing dust
c) Direct the exhaust so as to minimise disturbance of dust in a dust-filled
environment
d) Where dust or fumes are created, the priority should be to control them
at the point of emission
e) Select, maintain and replace the consumable/inserted tool as
recommended in the instruction handbook, to prevent an unnecessary
increase in dust or fumes
f) Use respiratory protection in accordance with employer's instructions
and as required by occupational health and safety regulations
Noise Hazards
a) Exposure to high noise levels can cause permanent, disabling hearing
loss and other problems, such as tinnitus (ringing, buzzing, whistling
or humming in the ears). Therefore, risk assessment and
implementation of appropriate controls for these hazards are essential
b) Appropriate controls to reduce the risk can include actions such as
damping materials to prevent workpieces from 'ringing'
c) Use hearing protection in accordance with employer's instructions and
as required by occupational health and safety regulations
d) Operate and maintain this tool as recommended in the instruction
handbook, to prevent an unnecessary increase in the noise level
e) Select, maintain and replace the consumable/inserted tool as
recommended in the instruction handbook, to prevent an unnecessary
increase in noise
f) If the tool has a silencer, always ensure it is in place and in good
working order when the tool is being operated
Vibration Hazards
a) This information shall draw attention to vibration hazards that have
not been eliminated by design and construction and remain as residual
vibration risks. It shall enable employers to identify the circumstances
in which the operator is likely to be at risk from vibration exposure. If
the vibration-emission value obtained using ISO 28927-3 does not
adequately represent the vibration emission in the intended uses
(and foreseeable misuses) of the machine, additional information and/or
warnings shall be supplied to enable the risks arising from vibration to
be assessed and managed.
b) Exposure to vibration can cause disabling damage to the nerves and
blood supply of the hands and arms
c) Wear warm clothing when working in cold conditions and keep your
hands warm and dry
d) If you experience numbness, tingling, pain or whitening of the skin in
your fingers or hands, stop using the machine, inform your employer
and consult a physician
www.silverlinetools.com
5