Audio Playback - THOMSON WEAR6309BT Mode D'emploi

5.1. Bluetooth pairing
®
Note – Pairing
• Make sure that your Bluetooth
and Bluetooth is activated.
®
• Make sure that your Bluetooth
visible for other Bluetooth
• For more information, please refer to the operating
instructions of your terminal device.
• The earphones and the terminal device should be no further than
one metre apart. The smaller the distance, the better.
• Switch on the earphones with the MF button (5).
• Press and hold the MF button (5) until the red and blue LEDs
ash alternatingly. The earphones are searching for a Bluetooth
connection.
• Open the Bluetooth settings on your terminal device and wait
®
until Thomson WEAR6309 appears in the list of Bluetooth
devices found.
• Select Thomson WEAR6309 and wait until the earphones are
listed as connected in the Bluetooth
device.
Note – Bluetooth password
®
Some terminal devices require a password in order to connect to
another Bluetooth device.
®
• If your terminal device requests a password for connection to
the earphones, enter 0000.
Note
• Once the connection has been established, a voice says,
"Connected".
• If the connection attempt takes longer than 300 seconds to
complete, it is cancelled and the LEDs go out.
• In this case, repeat the steps listed previously under 5.1
Bluetooth pairing.
®
5.2. Automatic Bluetooth
pairing)
Note
• Make sure that your Bluetooth
and Bluetooth is activated.
®
• Make sure that your Bluetooth
visible for other Bluetooth
• For more information, please refer to the operating
instructions of your terminal device.
• Switch on the earphones with the MF button (5). The blue LED
begins to ash and the earphones automatically connect with
the last terminal device used.
Note
• Once the connection has been established, a voice says,
"Connected".
-capable terminal device is on
®
-capable terminal device is
®
devices.
®
settings on your terminal
®
connection (after successful
®
-capable terminal device is on
®
-capable terminal device is
®
devices.
®
Note
• If the connection attempt takes longer than 300 seconds to
complete, it is cancelled and the LEDs go out. In this case,
repeat the steps listed previously under 5.2.
• It may be necessary to change the settings on your terminal
device to enable it to automatically connect to the earphones.
Note – Connection impaired
After the headset and terminal device have been paired, a
connection is established automatically. If the Bluetooth
connection is not established automatically, check the following:
• Check the Bluetooth
whether Thomson WEAR6309 is connected. If not, repeat the
®
steps listed under 5.1. Bluetooth
• Check whether obstacles are impairing the range. If so, move
the devices closer together.
®
• The performance can also be affected by a weak battery.
5.3. Bluetooth
®
These earphones can connect to two Bluetooth
devices simultaneously (multipoint).
• First connect the earphones with the rst terminal device as
described in 5.1.
• Then disable Bluetooth
• Next, connect the earphones with the second terminal device
as described in 5.1.
• Activate Bluetooth
earphones now connect to that terminal device automatically.

5.4. Audio playback

Note
• Note that the functions described under 5.3. and 5.4. are
only possible with an active Bluetooth
• Your terminal device must also support the individual
functions.
• For more information, please refer to the operating
instructions of your terminal device.
• Functions can still be controlled directly via the terminal device.
• Set the volume on your terminal device to a low level.
• Switch on the earphones with the MF button (5). Upon
successful connection, a voice says, "Connected".
• Start audio playback on the connected terminal device.
• Press Volume + (4) to increase the volume. There is an
announcement when the maximum volume is reached.
• Press Volume - (6) to reduce the volume.
• Press the MF button (5) to start or pause audio playback.
• Press and hold Jump forward one title (4) to skip to the
next title.
• Press and hold Jump backward one title (6) to skip to the
previous title.
settings of your terminal device to see
®
pairing.
®
multipoint connection
®
on that terminal device.
®
on the rst terminal device once more. The
®
connection.
®
®
-enabled terminal
3