Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
ENGLISH
(Original instructions)
Configuration of the "PROG" program
1. Setting the current time:
♦ Connect to the network and the system will show 12:00,
flashing.
♦ Press and hold the "PROG" button for 3 seconds. "SET
TIME" will appear on the screen, in the upper left corner .
♦ Press "HR" to set the time.
♦ Press "MIN" to set the minutes.
♦ Press and hold the "PROG" button again for 3 seconds
after finishing the time setting. Otherwise, the preset time
will be canceled after 10 seconds.
♦ If you unplug the device, the preset time will be canceled
and a restart will be required after plugging in the device
for the next use.
2. Setting the timer:
♦ Press and hold the "PROG" button (twice) for 0.5 sec-
onds to enter the setting condition.
♦ The words "SET TIMER" will appear blinking in the upper
right corner.
♦ Press the "HR" button for hours setting and press "MIN"
for minutes setting.
♦ Press and hold the "PROG" button for 0.5 seconds to
confirm.
♦ Press the "AUTO" button to switch the device to the
timer standby condition (the green LED will be on).
♦ Press the "AUTO" button again to switch off the standby
condition. Resume the wait condition by pressing the
"AUTO" button again.
♦ Press and hold the "PROG" button for 0.5 seconds to
check the preset time of the timer.
♦ Press "PROG" again to confirm and the screen will
return to the current time.
♦ Press "ON / OFF" at any time to switch on the appliance
and the red LED will light up.
♦ The device will start operating at the preset time (the red
LED will be on). The device will turn off automatically
after 40 minutes and the LCD will show the current time.
♦ Adjustable time range: 23 hours 59 minutes.
♦ "HR" time button: this button will only be used for time
setting. Press and hold this button for 0.5 seconds for
each hour increase. Keeping this button will make the
time settings run quickly.
♦ "MIN" minute button: same as the "HR" setting.
♦ WARNING: Do not leave the coffee machine unattended
while making coffee
6
Once the appliance is finished:
♦ Stop the appliance.
♦ You can press ON/OFF to stop, or you can just leave it
and it will turn off automatically after 40 minutes.
♦ Unplug the appliance from the main.
♦ Clean the device.
CLEANING
♦ Disconnect the appliance from the mains and allow it to
cool before undertaking any cleaning task.
♦ Clean the equipment with a damp cloth with a few drops
of washing-up liquid and then dry.
♦ Do not use solvents, or products with an acid or base pH
such as bleach, or abrasive products, for cleaning the
appliance.
♦ If the appliance is not in good condition of cleanliness, its
surface may degrade and inexorably affect the duration
of the appliance's useful life and could become unsafe
to use.
♦ To clean the permanent filter, empty it and rinse it with
running water
♦ The following pieces may be washed in a dishwasher
(using a soft cleaning program):
- Jug.
♦ Then dry all parts before its assembly and storage.
How to deal with lime scale incrustations:
♦ For the appliance to work correctly it should be kept free
of limescale or magnesium incrustations caused by the
use of hard water.
♦ To avoid this type of problem, it is recommended to use
water of low calcareous or magnesian mineralization.
♦ In any case, if it is not possible to use the type of water
recommended above, you should periodically proceed
with a decalcification treatment of the appliance, with a
periodicity of:
- Every 6 weeks if the water is "very hard".
- Every 12 weeks if the water is "hard".
- If the time needed to make a coffee jug increases
considerably
♦ A specific anti-lime scale product should be used on this
kind of product.
♦ Homemade solutions, such as the use of vinegar, are
not recommended in decalcification treatments of the
appliance.
Publicité
Table des Matières
