Black & Decker BCD003 Mode D'emploi page 7

The battery pack should be recharged when it fails to
u
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may also
charge a partially used pack whenever you desire with no
adverse effect on the battery pack.
Foreign materials of a conductive nature such as, but
u
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Unplug the
charger before attempting to clean.
Do not freeze or immerse the charger in water or any
u
other liquid.
Installing and removing the battery pack from the
tool (fig. B)
Warning! Make certain the lock-off button (2) is engaged to
prevent switch actuation before removing or installing battery.
To install battery pack:
Insert battery pack (7) into tool, until an audible click is
u
heard (fig. B)
Removing the battery pack from the tool (fig. C)
Depress the battery release button (8) as shown in (fig. C)
u
and pull battery pack out of tool.
Operating Instructions
Trigger switch & reversing button (fig. D)
The drill is turned ON and OFF by pulling and releasing
u
the trigger switch (1). The farther the trigger is depressed,
the higher the speed of the drill.
A forward/reverse control button (2) determines the direc-
u
tion of the tool and also serves as a lock off button.
To select forward rotation, release the trigger switch and
u
depress the forward/reverse control button to the left.
To select reverse, depress the forward/reverse control
u
button the opposite direction.
Note: The center position of the control button locks the tool
in the off position. When changing the position of the control
button, be sure the trigger is released.
Torque control (fig.E)
This tool is fitted with a torque adjustment collar (3) to select
the operating mode and to set the torque for tightening
screws. Large screws and hard workpiece materials require
a higher torque setting than small screws and soft workpiece
materials.
For drilling in wood, metal and plastics, set the collar to
u
the drilling position symbol
For screwdriving, set the collar to the desired setting. If you
u
do not yet know the appropriate setting, proceed as
follows:
(Original instructions)
Set the collar to the lowest torque setting.
u
Tighten the first screw.
u
If the clutch ratchets before the desired result is achieved,
u
increase the collar setting and continue tightening the
screw. Repeat until you reach the correct setting. Use this
setting for the remaining screws.
Keyless chuck (fig. F)
Warning! Make certain the lock-off button (2) is engaged to
prevent switch actuation before installing or removing acces-
sories.
To insert a drill bit or other accessory:
Grasp the rear half of the chuck (4) with one hand and use
u
your other hand to rotate the front half in the counterclock-
wise direction, as viewed from the chuck end.
Insert the bit or other accessory fully into the chuck, and
u
tighten securely by holding the rear half of the chuck and
rotating the front portion in the clockwise direction as
viewed from the chuck end.
Warning! Do not attempt to tighten drill bits (or any other ac-
cessory) by gripping the front part of the chuck and turning the
tool on. Damage to the chuck and personal injury may occur
when changing accessories.
Dual range gearing (Figure G)
The dual range feature of your drill allows you to shift gears
for greater versatility. To select low speed, high torque setting
(position 1), turn tool off and permit to stop. Slide gear shifter
button (5) away from the chuck. To select the high speed, low
torque setting (position 2), turn tool off and permit to stop.
Slide gear shifter button towards the chuck.
Note: Do not change gears when tool is running. If you are
having trouble changing gears, make sure that the dual range
gear button is either completely pushed forward or completely
pushed back.
Drilling/screwdriving
Select forward or reverse rotation using the forward/re-
u
verse slider (2).
To switch the tool on, press the switch (1). The tool speed
u
depends on how far you press the switch.
To switch the tool off, release the switch.
u
Hints for optimum use
Drilling
Use sharp drill bits only.
u
Support and secure work properly, as instructed in the
u
Safety Instructions.
Use appropriate and required safety equipment, as
u
instructed in the Safety Instructions.
Secure and maintain work area, as instructed in the
u
Safety Instructions.
ENGLISH
7