Sunex Tools SX1819TV Mode D'emploi page 2

FAILURE TO OBSERVE THESE WARNINGS COULD RESULT IN INJURY
THIS INSTRUCTION MANUAL CONTAINS IMPORTANT SAFETY
INFORMATION.
READ THIS INSTRUCTION MANUAL CAREFULLY AND
UNDERSTAND ALL INFORMATION BEFORE OPERATING THIS
TOOL.
• Read and understand all instructions. Failure to follow
all instructions listed below, may result in electric
shock, fire, explosion and/or serious personal injury. It is
the responsibility of the owner to make sure all personnel
read this manual prior to using the device. It is also
the responsibility of the device owner to keep this
manual intact and in a convenient location for all to
see and read. If the manual or product labels are lost
or not legible, contact Sunex Tools for replacements.
If the operator is not fluent in English, the product
and safety instructions shall be read and discussed
with the operator in the operator's native language by
the purchaser/owner or his designee, making sure that
the operator comprehends its contents.
• Always operate, inspect and maintain this tool in
accordance with American National Standards Institute
Safety Code of Portable Air Tools (ANSI B186.1) and any
other applicable safety codes and regulations.
• For safety, top performance and maximum durability of
parts, operate this tool at 90 psig; 6.2 bar max air
pressure with 3/8" diameter air supply hose.
• Always wear impact-resistant eye and face protection when
operating or performing maintenance on this tool. (users and
bystanders).
• High sound levels can cause permanent hearing loss.
Always use hearing protection as recommended by your
employer an OSHA regulations while using this tool
(users and bystanders).
• Keep the tool in efficient operating condition.
• Operators and
physically able to handle the bulk, weight and power of
this tool.
• Air under pressure can cause severe injury. Never direct
air at yourself or others. Always turn off the air supply,
drain hose of air pressure and detach tool from air supply
before installing, removing or adjusting any accessory
on this tool, or before performing any maintenance on
this tool. Failure to do so could result in injury. Whip
hoses can cause serious injury. Always check for
damaged, frayed or loose hoses and fittings, and replace
immediately. Do not use quick detach couplings at tool.
See instructions for correct set-up.
• Keep tool out of reach of children.
• Air powered tools can vibrate in use. Vibration, repetitive
motions or uncomfortable positions over extended
periods of time may be harmful to your hands and arms.
Discontinue use of tool if discomfort, tingling feeling or
pain occurs. Seek medical advice before resuming use.
• Slipping, tripping and/or falling while operating air
tools can be a major cause of serious injury or
death. Be aware of excess hose left on the walking
or work surface.
• Keep body working stance balanced and firm. Do
not overreach when operating the tool.
• Do not point or indulge in any horseplay with this tool.
SX1819TV: Parts Breakdown & Operating Manual
maintenance personnel must
WARNING
• Anticipate and be alert for sudden changes in motion
during start up and operation of any power tool.
• Do not carry tool by the hose. Protect the hose from
sharp objects and heat.
• Avoid direct contact with accessories during and after use.
Gloves will reduce the risk of cuts or burns.
• Keep away from end of tool. Do not wear jewelry or loose
clothing. Secure long hair. Scalping can occur if hair is not
kept away from tool and accessories. Choking can occur if
neckwear is notkept away from tool and accessories.
• Do not use (or modify) the tool for any other purpose
than that for which it was designed without consulting
the manufacturer's authorized representative.
• Do not exceed 100 psig maximum air pressure.
• Always disconnect air supply before proceeding with any
assembly or disassembly procedures.
• Keep exhaust port pointed away from face.
• Inspect the hydraulic section prior to use. Do not use if
cracked. Contact the distributor for repair or replacement.
• Do not pound on the nosepiece or the end of the head or
force the rivet into the hole of the nosepiece as this will
damage the tool.
• Make sure all parts are correctly and securely fastened.
• Always follow proper maintenance procedures.
• Keep clear of trigger when inserting rivets.
• Use accessories recommended by Sunex Tools.
• Do not lu bri cate tools with flam ma ble or vol a tile liq uids
such as ker o sene, die sel or jet fuel.
• This tool is not insulated against electric shock.
• This tool must not be used in explosive atmospheres.
• Servicing and repairs should only be made by an
authorized service center.
be
• Do not force tool beyond its rated capacity.
• Do not remove any labels. Replace damaged labels.
• This product may contain one or more chemicals known
to the State of California to cause cancer and birth
defects or other reproductive harm. Wash hands
thoroughly after handling.
• Handling the brass parts of this product will expose you
to lead, a chemical known to the State of California to cause
birth defects and other reproductive harm. Wash hands after
handling.
• Failure to heed these warnings may result in personal injury
and/or property damage.
2 Rev. 11/7/16