Bluetooth; Cleaning And Storing; Disposal - SilverCrest SSBS 36 A1 Mode D'emploi

BB72=  B6RXQGEDVHB%ERRN 6HLWH  'LHQVWDJ  -XOL    
1. Connect the socket HDMI (ARC)|10 by means of an
ARC-enabled HDMI cable to an HDMI ARC socket of
your television set.
2. Switch on the soundbase with the POWER
ton.
3. By pressing the HDMI (ARC)|17 button, select the
HDMI input.
4. Switch on the television set. When the connection is es-
tablished for the first time, it may take several seconds
until sound is output from the soundbase.

6.4 Bluetooth

Establishing connection
NOTES:
• The identification of the device is "SSBS|36|A1".
• After it has been switched over to Bluetooth, the device
automatically attempts to establish a connection with
the last paired device.
• Please observe that the establishment process of the
connection may vary slightly depending on the device
and the software used.
1. Press the |15 button to switch over to a Bluetooth
connection. LED|1 flashes blue.
2. Switch on the audio device (e.g. smartphone) and start
the Bluetooth connection.
3. The audio device will now receive the device identifi-
cation „SSBS|36|A1". If nothing happens, press the
PAIR|5 button on the device or the
the remote control for approximately 1 second. The
blue LED|1 flashes rapidly.
4. Establish the connection with the soundbase on the au-
dio device. If you are asked for a password, enter
"0000". Both devices are now interconnected. LED|1
now lights up in blue and a beep is heard.
NOTE: usually, audio devices remember the identification
of the device. In this case, it may not be necessary to es-
tablish the connection manually again if the Bluetooth func-
tion is activated.
5. Now play a music track on the audio device. The
sound is played back from the soundbase.
6. With the I WW |26, XX
can select and control the music tracks.
Interruption of the connection
The connection is interrupted if
... one of the devices is switched off;
... the Bluetooth function is switched off;
... the range (approx. 10 metres) is exceeded;
... you press the |15 or PAIR|5 buttons until the blue
LED is flashing. In this case, a new connection to an-
other device can be established immediately.
|29 but-
|15 button on
I|22 and X /II|25 buttons you

7. Cleaning and storing

DANGER! Risk of electric shock!
~ Pull the power unit|12 out of the wall socket before
you clean the device. Make sure that no liquid gets
into the device.
• Clean the device with a slightly damp cloth. In case of
persistent contamination, you can also use a slightly
more gentle cleaner such as detergent. Solvents, spir-
its, thinners etc. must not be used, as they can damage
the surface of the device.
• When not using the device, store it in a place where
neither high temperatures nor moisture can affect it.
Remove the battery from the remote control.

8. Disposal

This product is subject to the provisions of Eu-
ropean Directive 2012/19/EC. The symbol
showing a wheelie bin crossed through indi-
cates that the product requires separate re-
fuse collection in the European Union. This
applies to the product and all accessories marked with this
symbol. Products identified with this symbol may not be dis-
carded with normal household waste, but must be taken to
a collection point for recycling electric and electronic ap-
pliances. Recycling helps to reduce the consumption of raw
materials and protect the environment.
Batteries must not be discarded with your
household waste. Spent batteries must be dis-
posed of properly. Special containers are
available for this purpose in shops selling
batteries and at municipal collection points.
(Rechargeable) batteries marked with the following letters
contain harmful substances such as: Cd (cadmium), Hg
(mercury), Pb|(lead).
Packaging
When disposing of the packaging, make sure you comply
with the environmental regulations applicable in your
country.
GB 17