WOLFF VARIO-STRIPPER 230 V/50 Hz Traduction Du Mode D'emploi Original page 21

The VARIO-STRIPPER is primarily used to remo-
ve linoleum, PVC, rubber, cork, design, and CV
coverings as well as needle-punched floor cover-
ing and carpeted flooring.
Hardwood parquet, multi-layer parquet, semiflexi-
ble and ceramic tiles can also be removed to a
limited extent.
► Needle-punched floor covering, carpet, PVC.....
The coverings to be removed should be pre-cut in
blade-widths (fig. G) and then removed with the
stripper in one step. In many cases, the glue can
also be removed at the same time.
► Coverings without a foam backing:
Prior to performing the stripping work, pre-cut the
strips in blade-widths (fig. G). Regularly check
whether the blade is still straight and sharp.
► Coverings with a foam backing:
Only use sharp blades! Remove the large sections
of the wearing surface. Use a carpet pulling claw for
this.
Then remove the foam residue with the stripper. If
there is some foam in the recess, approach from
the side.
► Coverings with a fleece backing:
Do not remove the wearing surface beforehand. Cut
the covering into strips and strip them together with
the fleece backing.
► Semi-flexible tiles:
Provided they are not extremely flexible, semiflexible -
tiles can be removed without pre-cutting them.
Attention
Important blade recommendation!
In general, no statements can be made on which
blades can be used for which blades, because the
variety of coverings and surfaces are too diverse.
These recommendations are to provide assistance!
► With U-blades, the pre-cutting step in not necessary
for many flexible coverings, the coverings must be
checked on-site.If the tyre wear is highly visible on
the surface, the U-blade should not be used.
Wolff GmbH & Co KG | D-74360 Ilsfeld | Ungerhalde 1 | Fon: +49 (0)7062-91556-0 | Fax: +49 (0)7062-91556-41 | www.wolff-tools.de
► The blade is generally inserted with the blade edge
up, unless it works itself too deep in the surface. In
this case, the blade must be inserted with the blade
edge down.
10.0 Guarantee
The warranty period for new Wolff machines shall last for
one year from the point at which the machine is transfer-
red / delivered to the customer, insofar as statutory legal
requirements do not stipulate otherwise.
When validating warranty claims, the invoice or proof of
purchase must always be submitted. All repairs within the
framework of the warranty agreement must be undertaken
by a service Centre that has been accredited by us.
Customers performing their own repairs and/or improper
repairs regularly lead to the exclusion of warranty claims.
The same also applies to incorrect operation and/or use.
Replacement of parts, accessories and other modifica-
tions to Wolff machines
Users of Wolff machines enjoy a high level of safety and
reliability of their machine. In order to maintain this status
quo, your Wolff tool may not be modified from the condition
in which it is delivered without following the rules below.
These rules apply to both the replacement of parts and
equipping the machine with accessories as well as other
technical modifications.
 All work undertaken to your Wolff machine must
be undertaken exclusively by a workshop that
has suitably trained and experienced personnel at
its disposal, as well as the requisite work equip-
ment. We recommend using authorised service
Centre.
 In the event of planned replacement of parts, plan-
ned addition of accessories or other planned
technical modifications, an assessment must al-
ways be carried out by an authorised service
Centre or us, as manufacturer, before work is com-
menced.
 It is highly recommend that only safety-approved
Original Wolff replacement parts and Original Wolff
accessories are used, which have been approved
by us, as manufacturer. Replacement parts and
accessories can be obtained from your authorised
EN
21