General Description - Italkero Falo Evo Instructions D'installation Et D'utilisation

GenerAl deScription

Due to its specific type of operation with direct and reflected irradiance, this appliance approximately heat up a surface of 13 m2
with a range of action of 2 meters. The weather of your specific region could influence the device efficiency, as the appliance
position (totally or in part open space) as your subjective heating feelings. The heating feeling substaintially increases close to
the appliance.
The appliance is very simple to use and built according to CE safety standards. It has been tested, approved and controlled by
the Notified Approval Institute to which the Manufacturer has always entrusted most of its certifications in the gas industry.
Types of installation:
- MOBILE, with the base free of restraints using the trolley (optional), with LPG fuel only (tank).
- FIXED, with the base fastened to the floor (this type of installation must be carried out only by professionally skilled personnel),
using Propane/Butane gas (large tank) or natural mains gas.
ASSemBlY
Take all the parts making up the appliance out of the packaging, with special care given to the burner unit (Fig. 3).
Check the integrity and the conformity of the contents of the packaging (the latter must be disposed of according to applicable
regulations):
A - Mod. FALO' with manual controls
- Appliance with carrying structure and special-glass pipe;
- Hose connection (make sure this complies with applicable regulations);
- Cover dish;
- Multilingual instruction booklet;
- Warranty Certificate.
B - Mod. FALO' with Remote Control
- Appliance with carrying structure and special-glass pipe;
- Hose connection (make sure this complies with applicable regulations);
- Cover dish;
- Multilingual instruction booklet;
- Warranty Certificate.
IMPORTANT! Always wear individual hand protection gear during appliance assembly and positioning. Use the special accesso-
ry for moving (Fig. 3, Fig. 12) to prevent cuts and burns.
ASSEMBLY OPERATIONS (MOBILE type with LPG tank):
Before starting assembly operations, remove any guards.
1 – Delicately place the structure on the ground and fit the cover dish (Fig. 3: 2).
2 – Remove the side panels (Fig. 3) and position the tank on the base plate (Fig. 3).
3 – Fit the gas pressure regulator on the cylinder (fixed-setting type) in conformity with the TECHNICAL DATA and GAS
SETTING plates on the appliance.
4 – Purchase the connector and the rubber connection hose separately. These must be of the type and materials required by
the Regulations of the Country of use (if those already provided do NOT conform).
The threaded end part, meaning the adapter (Fig. 9: 4) permits various kinds of connections.
IMPORTANT! two types of adapters exist, one left turning (SWITZERLAND, AUSTRIA, GERMANY and LUXEMBOURG) and
one right turning (all other countries).
CASE A (Fig. 9: A) 1/4" gas left turning: fit the rubber hose (1), featuring a specific threaded connector (SUPPLIED). This solu-
tion is suitable for SWITZERLAND, AUSTRIA, GERMANY and LUXEMBOURG.
CASE B (Fig. 9: B) 1/4" right turning: fit the rubber hose (6) purchased separately (if that already provided does NOT comply)
directly on the threaded 1/4" GAS right turning connection (4) of the end part ; now fit the rubber hose (8- MAX Length = 1.5 m)
using the clamp provided (6).
5 – Fasten the lower part of the gas connection hose to the regulator (Fig. 9: 2) on the tank (Fig. 9: 3). Connect the other end of
the gas hose to the connection.
6 – Before making the connection, check to see whether the gas diaphragm (Fig. 9: 5) must be fitted on the entry connector
(Fig. 9: 4) (solution valid for SWITZERLAND, AUSTRIA, GERMANY and LUXEMBOURG - see Tab.).
IMPORTANT! DO NOT FIT the diaphragm on appliances fuelled with gas G30/G31 at 29÷37 mbar.
IMPORTANT! ONLY FIT the diaphragm in case of operation with supply pressure 50 mbar (Switzerland, Austria, Germany,
Luxembourg). Check the correct type as specified and shown on Tab..
7 – Delicately tilt the appliance, position the cover dish (Fig. 3: 2) and fasten in position with the knobs provided (Fig. 3: 1) and
return the appliance to vertical position.
IMPORTANT! NEVER rest the top end of the appliance on the ground, especially when the cover dish is fitted to avoid dama-
ging the gas seals, the glass pipe or obstructing the gas pipe.
8 – Connect the gas supply pipe to the bottom part of the connection (already fitted) (Fig. 7 and 8: 12).
UK
26