VOLTCRAFT VC-65WC-PD Mode D'emploi page 3

Operating instructions
VC-65WC-PD USB Charging Station 65 W
Item no. 2160339
Intended use
The product has three USB-A outputs and one USB-C™ output. The product is suitable for
charging and operating up to four USB devices at the same time. Power is supplied via a
standard household mains socket. The product is protected against short circuit and overload.
This product is intended for indoor use only. Do not use it outdoors. Contact with moisture
(e.g. in a bathroom) must be avoided under all circumstances.
For safety and approval purposes, do not rebuild and/or modify this product. Using the product
for purposes other than those described above may damage the product. In addition, improper
use can cause hazards such as a short circuit, fire or electric shock. Read the operating
instructions carefully and store them in a safe place. Only make this product available to third
parties together with its operating instructions.
This product complies with statutory, national and European regulations. All company and
product names contained herein are trademarks of their respective owners. All rights reserved.
Package contents
• USB charging station
• Power cable (about 1.2 m in length)
Up-to-date operating instructions
To download the latest operating instructions, visit www.conrad.com/downloads
or scan the QR code on this page. Follow the instructions on the website.
Explanation of symbols
The symbol with the lightning in a triangle indicates that there is a risk to your health,
e.g. due to an electric shock.
The symbol with an exclamation mark in a triangle is used to highlight important
information in these operating instructions. Always read this information carefully.
The product must only be installed and used in dry, indoor locations. It must not
become damp or wet, as this may cause a fatal electric shock!
Safety instructions
Read the operating instructions carefully and observe in particular the safety
instructions. If you do not follow the safety information and information on
proper handling in these operating instructions, we will assume no liability for
any resulting personal injury or damage to property. Such cases will invalidate
the warranty/guarantee.
a) General information
• This product is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. It may become a
dangerous toy for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, stop using it and prevent
unauthorised use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stress.
• Handle the product carefully. Jolts, impacts or a fall even from a low height may
damage the product.
• The mains outlet must be located near to the device and be easily accessible.
• Unplug the connected USB device from the product when you are not using it.
• Electrical devices must never be plugged in or unplugged with wet hands.
• Operating instructions
• If the product shows signs of damage, do not touch it, there is a risk of death
from an electric shock! First, switch off the mains voltage to the mains socket to
which the product is connected (switch off the respective circuit breaker or remove
the safety fuse; then switch off the respective GFCI so that the mains socket is
fully disconnected). You can then unplug the mains plug from the mains socket.
Dispose of the damaged product in an environmentally friendly manner, stop using
it. Replace it with an identical product.
• The product must only be powered by a standard mains socket connected to the
public grid. Before plugging in the product, check that the voltage indicated on the
product corresponds to the voltage of your electricity supplier.
• Never disconnect electrical equipment from the power outlet by the cable, always
pull it out of the mains socket by gripping surfaces provided for this purpose.
• When setting up the product, make sure that the cables are not pinched, kinked
or damaged by sharp edges.
• Always lay the cables so that nobody can trip over or become entangled in them.
This poses a risk of injury.
• For safety reasons, disconnect the product from the mains socket during storms.
• Never pour liquids over electrical devices or place objects filled with liquid next to
the device. If liquid or a foreign object enters the interior of the device nevertheless,
first power down the respective mains socket (e.g. switch off the circuit breaker)
and then pull the mains plug from the mains socket. Do not operate the product
any more afterwards, but take it to a specialist workshop.
• Never use the product immediately after it has been brought from a cold room into
a warm one. The condensation that forms may destroy the product. Furthermore,
it can cause a lethal electric shock! Allow the product to reach room temperature
before connecting it and putting it into use. This may take several hours.
• Make sure the USB ports are not short-circuited.
• Ensure there is sufficient air circulation when you operate the product. Never
cover the product.
• Consult a technician if you are not sure how to use or connect the product, or if
you have concerns about safety.
• Maintenance, modifications and repairs must be carried out by a technician or a
specialist repair centre.
• If you have any questions which are not answered in these operating instructions,
contact our technical support service or other technical personnel.
b) Connected devices
• Always observe the safety instructions and operating instructions of any other
devices which are connected to the product.
• Always switch off the USB device to be connected before connecting and
disconnecting.
Product overview
1
1 Power cord socket
2 LED operation lamp
3 USB-C™ output USB-C PD
Setup
• Connect the connector of the supplied power cord to the power cord socket (1). Place
the USB charging station on a levelled and clean surface. Connect the power plug to an
appropriate power outlet. The LED operation lamp (2) lights up.
• Connect a switched off USB device to one of the USB-A outputs FastCharge (4), 2.4 A
the USB-C™ output USB-C PD (3). You can charge up to four devices at the same time. Please
note the available charging currents, see section "Technical data".
• The USB device will start to charge. Should you wish to operate the USB device, you may
turn it on now. Turn off the USB device before removing the product from the mains socket.
• Fast charging is possible via the USB-A FastCharge output. In addition, devices with different
voltages (3.6 - 6 V, 6 - 9 V and 9 - 12 V) can be charged at this output.
• The USB-C™ output USB-C PD can be used to charge devices with different voltages
(5 V, 9 V, 12 V, 15 V, 20 V) and with USB Power Delivery (PD 45 W).
• Disconnect all connected USB devices from the USB charging station after use. Disconnect
the USB charging station from the mains socket after use. The LED operation lamp goes out
after approx. 30 seconds.
4 USB-A output FastCharge (fast charging)
5 USB-A output 2.4 A
(2 x)
MAX.
MAX.
2
3
4
5
(5) or