Initial Operation; Using The Appliance - Clatronic CL 3542 Mode D'emploi

Initial operation

Location
• When installing the device, make sure to keep a distance of at
least 50 cm between the unit and any walls or other objects.
• The surface must be flat and dry.
Assembly of exhaust pipe
NOTE:
For sliding windows, you may use the window kit provided and
install it in a vertical or horizontal position. Adjust the length of
the seal plate as desired.
1. Turn the adapter (8) to one end of the exhaust pipe.
2. Connect the exhaust pipe to the unit using the exhaust pipe
connector. Turn the pipe anticlockwise several times. Make
sure the pipe is securely connected.
3. Extend the pipe to the desired length.
4. Stick the open end of the pipe into a window.
5. Close the window as far as possible. Also lower any external
roller blinds, if present, to the end of the pipe.
Remote control
1. Open the battery compartment cover on the back of the
remote control.
2. Insert 2 batteries of type R03 "AAA" 1.5 V, observing the cor-
rect polarity (see markings on the bottom of the compartment)!
3. Close the battery compartment cover.
Mains connection
1. Make sure the mains voltage you want to use corresponds to
the voltage of the unit. Please check the rating label for de-
tailed specifications.
2. Connect the unit to a properly installed grounded socket. A
signal will sound indicating that the unit is ready for use. The
display will show the current room temperature with low illumi-
nation.

Using the Appliance

Turning unit on/off
• Press the POWER button to turn on the unit. During ini-
tial operation, the display will show the default setting
"Cooling" and 22 °C. If operation has been stopped without
disconnecting the plug, all previously set operating mode and
temperature settings will be retained. In that case, the display
will show these settings instead.
• Press the POWER button again to turn off the device. The
display will again show the current room temperature with low
illumination.
Operating modes
Use the MODE button to select one of the following operating
modes:
• Cooling
• Dehumidifying
• Fan
The display will show the respective icon.
Setting the temperature
Use the UP or DOWN
the temperature. Select a temperature between 16°C and 31°C.
Setting the fan
In "Cooling" and "Fan"
with 2 different settings. Press the VENTILATOR
cordingly.
Setting the air outlet
Adjust the fins to regulate the direction of discharged air.
• Use the lever (1) to adjust the fins to the right / left.
• Turn one of the fins in order to direct the air upwards / down-
wards.
Setting the sleep mode
• When in "Cooling"
activate the sleep mode.
• After one hour of operation the system will increase the pre-
viously selected temperature by 1°C. After another hour of
operation the system will increase the temperature again by
1°C. There will be no further adjustments after that.
• In sleep mode, the fan operates at the lowest speed setting.
This setting cannot be changed.
• Sleep mode cannot be activated when in "Dehumidifying"
mode.
Dehumidifying
• This operating mode does not support any further settings.
• The fan will operate at the lowest speed setting.
• After approx. 3 minutes of operation the compressor will turn
on and the display will in addition show the
• The unit will cool the room and extract the humidity from the
air.
Timer (Automatic timer)
Use the timer function to set the power-on and power-off times of
the device. Select a time between 1 and 24 hours.
Using the timer function for automatic power-on
1. Press the POWER
for
2. Select the operating mode, temperature and fan speed for the
unit to operate in or at when powered on at the pre-set time.
3. Press the POWER
4. Press the TIMER
desired. The display will show the
which the unit will power on automatically.
Using the timer function for automatic power-off
1. Press the POWER
2. Press the TIMER
set the hours as desired. The display will show the
The hours after which the unit will power off automatically, will
briefly flash.
NOTE
• In order to deactivate the timer function, use the
and select "00".
buttons in "Cooling" mode to set
modes you can set the fan speed
button ac-
mode, use the SLEEP button to
icon.
button to turn on the unit.
button to turn off the unit.
button repeatedly to set the hour as
icon and the hours after
button to turn on the unit.
button repeatedly during operation to
button
icon.
33