Sleep Timer Setting - CAPTELEC PCR-2228 Mode D'emploi

R 2228 / PCR-2228
5. Now press AL1/VOL- button (5) repeatedly to choose the alarm status.
The status indicators for Alarm 1 appear in the following sequence on the LEFT of the display:
A) Wake To Buzzer: Alarm 1 Buzzer indicator (11) is lighted up and Alarm time is flashing on the display.
B) Wake To Radio: Alarm 1 Radio indicator (12) is lighted up and Alarm time is flashing on the display.
C) Alarm Off: All Alarm 1 indicators are off and the current time is shown on the display.
5 seconds after the desired status is chosen, the display will stop flashing and change to show the current
time. Please make sure the indicator for the selected status (buzzer or radio) is ON, or no indicator is on in
case if you choose to turn off the alarm.
6. To use Alarm 2, just follow steps 2 to 5 with using the AL2/VOL+ button (6) instead of AL1/VOL- button (5).
Similarly, the Wake To Buzzer indicator is Alarm 2 Buzzer indicator (14) and the Wake To Radio indicator is
Alarm 2 Radio indicator (15) on the RIGHT of the display.
7. When the Alarm sounds, you can either:
A) Press RADIO ON/RADIO OFF Button (7) once to switch off the alarm. You can see that the alarm indicator
is still on, showing that the alarm function is still activated and will sound again after 24 hours.
B) Press the SLEEP/SNOOZE button (9) to temporarily turn the alarm off for 9 minutes. (See SNOOZE
SETTING below)
C) If no button is pressed after the alarm sounds, the alarm will continue sounding and automatically turn
off at 1 hour after the alarm time.
D) To disable the alarm completely, press AL1/VOL- button (5) or AL2/VOL+ button (6) until their indicators
(radio or buzzer) disappear from the display.
Notes:
The sound cannot be adjusted for the Wake To Buzzer alarm.
1.
The Alarm 1 (or 2) indicator will flash on the display when the alarm sounds.
2.
If a later alarm sounds when the earlier alarm is still sounding, the later alarm will take priority.
3.
If a later alarm sounds when the earlier alarm is in SNOOZE, then the later alarm will take priority and cancel
4.
the SNOOZE function of the earlier alarm automatically.
If the same time is set for both alarm (Alarm 1 or 2), Alarm 1 takes priority.
5.
SNOOZE SETTING
Once the alarm starts sounding, the snooze function can be used to stop the alarm temporarily for 9 minutes
before it sounds again.
1) When Alarm 1 or 2 sounds, press the SLEEP/SNOOZE button (9) to stop the buzzer or radio alarm. The alarm
will sound again after about 9 minutes. The SNOOZE function can be repeated within 1 hour from the set
alarm time.
2) During the time when SNOOZE function is activated, the corresponding alarm indicator will flash.
3) To switch off the SNOOZE function, simply press RADIO ON/RADIO OFF Button (7) once.
The alarm indicator will stop flashing and the alarm will not sound again until the set time on the next day.

SLEEP TIMER SETTING

The SLEEP timer function allows the radio to play in blocks of 10, 20, 30, 40, 50, 60, 70, 80, or 90 minutes before
turning off automatically, so you can enjoy falling asleep when listening to the radio.
1) When you listening to the radio, press the SLEEP/SNOOZE (9) button with the display showing 90(for 90
minutes). Press the SLEEP/SNOOZE (9) button repeatedly until the display shows your desired SLEEP time
period. The time period is shown on the display in sequence as 90 > 80 > 70 > 60 > 50 > 40 > 30 > 20 > 10 >
OFF.
2) 2 seconds after the desired SLEEP period is chosen, the display will change back to show the current time,
and the radio will play for the SLEEP time duration you have set and then turn off automatically.
3) Press the SLEEP/SNOOZE (9) button again during SLEEP mode, the LED will show the remaining time of the