Ec Declaration Of Conformity; General Power Tool Safety Warnings - DeWalt XR DCM563P1-QW Traduction De La Notice D'instructions Originale

Denotes risk of electric shock.
Denotes risk of fire.
EC-Declaration of Conformity
MACHINERY DIRECTIVE
OUTDOOR NOISE DIRECTIVE
HEDGE TRIMMER
DCM563
D WALT declares that these products described
e
under Technical Data are in compliance with:
2006/42/EC, EN 60745-1:2009 + A11:2010; EN
60745-2-15:2009 + A1:2010
2000/14/EC, Blower, Annex VI
DEKRA Certification B.V., Utrechtseweg 310,
6802 ED Arnhem, The Netherlands
Notified Body ID No.: 0344
Level of accoustic power according to 2000/14/EC
(Article 13, Annex III):
L (measured sound power) 91.5 dB(A)
WA
Uncertainty = 3 dB(A)
L (guaranteed sound power) 98 dB(A)
WA
These products also comply with Directive
2004/108/EC (until 19.04.2016), 2014/30/EU (from
20.04.2016) and 2011/65/EU. For more information,
please contact D WALT at the following address or
e
refer to the back of the manual.
The undersigned is responsible for compilation of
the technical file and makes this declaration on
behalf of D WALT.
e
Markus Rompel
Director Engineering
D WALT, Richard-Klinger-Straße 11,
e
D-65510, Idstein, Germany
DD.MM.2015
WARNING: To reduce the risk of injury,
read the instruction manual.

General Power Tool Safety Warnings

WARNING: Read all safety warnings
and all instructions. Failure to follow the
warnings and instructions may result in
electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term "power tool" in the warnings refers to
your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1) WORK AREA SAFETY
Keep work area clean and well lit.
a)
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
Keep children and bystanders away
c)
while operating a power tool. Distractions
can cause you to lose control.
2) ELECTRICAL SAFETY
Power tool plugs must match the outlet.
a)
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators. There
is an increased risk of electric shock if your
body is earthed or grounded.
Do not expose power tools to rain or wet
c)
conditions. Water entering a power tool will
increase the risk of electric shock.
Do not abuse the cord. Never use the
d)
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors,
use an extension cord suitable for
outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric
shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric
shock.
3) PERSONAL SAFETY
Stay alert, watch what you are
a)
doing and use common sense when
operating a power tool. Do not use
a power tool while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
english
29