ubbink Outside Living Industries 410 Notice De Montage page 19

SUMMARY :
- Preparing the ground
- Erecting the sides of the pool
- Screwing in the brackets
- Installing the tracks
- Installing the felt underlay and
the liner
- Cutting out the liner, fitting the
backwash inlet nozzle and the skimmer
- Assembly of the pine edging
- The ladders
3a - Mark in where the brackets will go.
3b - Mark in the pre-drilling points for the brackets on the skimmer side of the pool.
3c - Position the brackets.
3d - Secure the wooden stops for the skimmer flap.
3e - Once you have put Teflon tape round the fitting that has been fed through, screw the stop valve that has been fed through into the body of the skimmer.
Shut off the valve.
4a - Drill the tracks according to the measurements (3 cm from the ends and then approximately every 20 cm). The tracks can be adjusted to the required
length.
4b - Screw in the first track of the liner.
4c - Mark in where the corner cut is to be made.
4d - Cut the corners according to the diagram.
5a - Put the protective felt underlay in place.
5b - Cut out the felt underlay using a Stanley knife or a pair of scissors.
5c - Put the liner in place.
5d - Fit the corners of the liner into the corners of the structure.
5e - Hook the liner on to the lip of the track.
5f - Check the position of the liner and smooth out the biggest creases on the bottom of the pool towards the sides.
5g - Check the position of the liner and smooth out the creases on the sides of the pool.
5h - Fill the pool with water to a depth of 2 cm.
5i - Smooth out all the creases.
5j - Resume filling with water.
6a - Stop filling when the water is just below the backwash inlet nozzle.
6b - Position the backwash inlet nozzle from the inside of the pool.
6c - Cut out the liner for the backwash inlet nozzle, leaving about 2 mm play around it.
6d - Bind the ends of the fittings that have been fed through with Teflon tape, working in an anti-clockwise direction. Wrap round at least 20 times.
6e - Screw one of the ends to the backwash inlet and the other one under the skimmer.
6f - Install one of the pipes to the backwash inlet and secure it in place using a metal collar.
6g - Put the other end of the pipe into the swimming pool and resume filling with water.
6h - Mark in the position of the skimmer seal.
6i - Put in the skimmer seal and the frame. The screws provided are in the skimmer pack.
6j - Cut out the liner on the inside of the skimmer frame
6k - The water is at the correct level when it is halfway up the skimmer (after you have put in the filter).
7
• (see page 28)
8
8a - Put the ladder in position. To do that, expel the air from the steps if necessary.
8b - Nail the warning notice regarding the need for adult supervision either to the side of the pool or within very close proximity of the pool.
You should also nail the notice about the exterior ladder to one of the posts.
1a- Mark out the position of the structure on the ground allowing a 50 cm margin so that it is easier to check
your measuring.
1b - Make a concrete slab to the dimensions detailed on page 12; it must be a minimum
thickness of 10 cm.
1c - Position the swimming pool so that the skimmer will be facing the prevailing wind, which guarantees the
most efficient removal of particles from the surface. For that, to temporarily use the first rank of plank.
A half plank must be plumb with the skimmer.
You must have a concrete slab in place if your guarantee is to be validated
2a - Key point for assembling the structure. Do not hammer directly on to the planks when fitting them together;
use the cale (the protective piece of wood).
2b - Put in the bottom row of planks.
2c - Check your measurements are accurate with a 10m tape.
2d - Check your measurements are accurate with a 10m tape.
2e - Position the plank for the backwash inlet, It can be placed to the right or the left of the skimmer.
2f - Position the lower plank for the skimmer.
2g - Install the skimmer.
2h - Position the upper skimmer plank and the remaining upper planks.
2i - Check that the structure is level.
2j - Stick double-sided adhes
2k - Put in the skimmer seals.
If using a safety tarpaulin, make sure to centre
the stainless steel ladder on the edging
18