Spare Parts; Disassembling, Demolition And Elimination Of Residuals; Chapter 8. Guarantee; Certificate Of Guarantee - Minipack-Torre FM75 Digit Instructions Pour L'installation, L'emploi Et L'entretien

Chapter 7. Ordinary maintenance

7.8. Spare parts

Code FM75
S01A0404
FE385601
FM350008
FM350005
S0K00306
FE241011 (230V)
FE241012 (115V)
FE240017 (200V)
FM130001
FM080038
FM170001
S0K00604
S0K00605
FE381001+FE381002 (230V)
FE381003+FE381004 (115V)
FE381005+FE381006 (200V)
S01A0602
S0K01111
FM195011
FE440602 (230V)
FE440601 (115V)
FE440602 (200V)

7.9. Disassembling, demolition and elimination of residuals

ATTENTION!
All operations about disassembling and demolition must be done by qualified personnel with mechanical
and electrical expertise required to work in security conditions.
Proceed as follows:
1. disconnect machine from power mains
2. disassemble components
All wastes must be treated, eliminated or recycled according to their classification and to the procedures in
force established by the laws in force in the country the equipment has been installed.
The symbol indicates that this product shall not be treated as household waste.
By assuring that the product will be properly disposed of, you will facilitate the prevention of potential
negative effects for the environment and the man's health, which might be otherwise caused by the
improper waste treatment of this product.
For more detailed information about the recycling of this product, please contact the product seller or, as
an alternative, the after-sales service or the corresponding waste treatment service.

Chapter 8. Guarantee

8.1. Certificate of guarantee

The guarantee runs for 12 months after the installation date under the conditions set forth on the instruction manual. Fill
in the card with all data requested,tear out along the perforations and send in.

8.2. Guarantee conditions

The guarantee runs for 12 months and goes into force on the installation date of the machine. The guarantee covers free
replacement or repair of any parts due to defects arising from faulty material. The repairs or replacement are usually
carried out at the manufactures, with transport or workmanship at buyer's charge. If the repair or replacement is carried
out at the buyer's place, he shall bear the travelling, transfer and workmanship charges. Work under guarantee can be
carried out exclusively by the manufacturer or by the authorised dealer. In order to be entitled to repairs under the
guarantee, the faulty part must be sent for repair or replacement to the manufacturer or his authorised dealer. The return
of such repaired or replaced part will be considered to be the performance of the guarantee. The guarantee is voided:
1. in case of failure to mail the CERTIFICATE OF GUARANTEE, duly filled in and signed, with in 20 days after the date
of purchase.
2. in case of inappropriate installation, power supply, misuse and mishandling by unauthorised persons.
3. in case of changes made to the machine without prior agreement in writing by the manufacturers.
4. if the machine is no longer the property of the first buyer.
The manufacturer decline any responsibility for damage to persons or things in case of inappropriate
installation or connection to the power mains or omission of connection to earth or in case of any mishandling
of the machine. The manufacturer undertake to carry out any variations and changes made necessary by
technical and operating requirements
Code FM76
S02A0404
FE385602
FM350009
FM350006
S0K00306
FE240019 (230V)
FE240029 (115V)
FE240023 (200V)
FM130002
FM080037
FM170002
S0K00604
S0K00605
FE381011+FE381012 (230V)
FE381013+FE381014 (115V)
FE381019+FE381020 (200V)
S02A0602
S0K01110
FM195012
FE440612 (230V)
FE440611 (115V)
FE440612 (200V)
.
16
Item description
Teflon liner
Sealing blade
Upper neoprene rubber
Lower neoprene rubber
Blade holder complete clamp
Motor
Reticulated plate
Upper hood
Torsion bar
Complete slotted microperforator
Complete needles microperforator
Resistors
Roll holder complete tube
Fan
Glass wool panel
Transformer
GB
GB