Instruction Manual Resistance Welder Spotter - Spotter 7630 Manuel D'instruction

INSTRUCTION MANUAL RESISTANCE WELDER SPOTTER

INTRODUCTION
CAREFULLY READ THIS MANUAL BEFORE INSTALLING
OPERATING WELDER
This welder has been designed for : resistance welding of nails,
washers for sheets straightening; screws and rivets welding;
sheets localised heating. The welder must not used for other
applications.
This welder shall be used only for professional purposes in an
industrial environment. There could be some difficulties in
assuring the electromagnetic
environments. All modifications, even slight ones, are forbidden
because they should invalidate the welder EC certification.
Item S07630 includes :
337600 - Spotter
337601 - Slide hammer
337602 - Electrode ∅ 2,5 to weld nails
337603 - Electrode ∅ 4 for screws
337604 - Magnetic electrode for trim rivets welding
337610 - Nails ∅ 2x50, package of 100 pieces
337612 - Screws M4x16, package of 100 pieces
337613 - Trim rivets, package of 100 pieces
337614 - Washers ∅ 9x16mm, package of 50 pieces
337605 - Electrode for washers
337606 - Electrode for item 337605
337608 - Hook for washers
337618 - Box for nails, washers, screws, rivets
337002 - Handle
Suitcase
The manufacturer in not responsible for any damage to both
people, animals, things and to the welder itself caused by
either a wrong use or the lack or the superficial observance of
the safety warnings stated on this manual, nor it is responsible
for damages coming from even slight tampering or from the
use of not-suitable spare parts and accessories, or of spare
parts and accessories other than the original ones.
TECHNICAL FEATURES
Input voltage/ 230V/50Hz
frequency
Nominal power at 0,8 kVA
50% duty cycle
Maximum welding 5,2 kVA
power
Short circuit 2,5 kA
secondary current
Secondary no load 2,6 V
alternate voltage
Fuses 16 A
Force to apply to 15÷25 daN
the tool
Net weight 5,8 kg
without cord
Aerial noise produces
(Continuous equivalent acoustic pressure level)
Vibrations level
compatibility in
< 70 dB (A)
2
< 2.5 m/s
WELDER SET UP
On receipt of the machine verify the perfect integrity of the
outer package; communicate to a responsible in charge
possible anomalies which should be noticed. Possible
damages on the outer package should arise some doubts on
the integrity of its content. Remove the package and visually
verify the machine integrity. Check that the welder is equipped
with all the standard components: immediately inform the
manufacturer in case some components should lack. All the
material forming the package must be removed according to
the present environmental protection regulations.
other
As the welder can be supplied for different power supplies,
before connecting the unit to the power line check if the voltage
shown on the spotter feature plate corresponds to the mains
one.
This machine is equipped with a plug; all use without plug is
forbidden. If replacing the plug, chose one having a capacity
equal to or higher than supplied one, equipped with grounding.
It is compulsory to use a socket equipped with a good
grounding and protect by either a magneto-thermal switch or
fuses.
We recommend not to use extensions on the welder; if this
proves to be necessary, they must be as short as possible and
must have a proper section in comparison with their length.
SAFETY RULES
The welder must be installed in a position fulfilling the following
features:
- In a inner place. The use of the welder in an open place is not
foreseen.
- Room temperature included between 0 and 40°C; 1000 m.
maximum altitudes.
- In a well ventilated area, free from dust, steam, and acid
exhalations.
- The working place must be free from inflammable materials
because the working process can produce sparks.
In case the material to be welded produces either smoke or
exhalations, install a proper aspirator.
Notice that these types of machines generate magnetic
fields attracting metals and damaging watches and
magnetic cards. Since these magnetic fields can affect
pace-makers, the wearers must consult their doctor before
approaching to the welding area.
The personnel must wear both safety glasses and gloves.
Avoid wearing rings, metal watches and clothes with
either metal accessories or components.
In case of water entering the welder, immediately stop the
electrical supply.
Never carry the spotter by its cord or yank it to disconnect it
from the socket. Keep the cord away from heat, oil and sharp
edges.
In addition to the information stated on this chapter, always
operate in accordance with all the relevant laws in force.
4