Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
TABLE OF CONTENTS
SCHEMATIC DRAWING
PARTS LIST
IMPORTANT SAFETY INSTRUCTIONS
SAFETY PRECAUTIONS FOR COMPRESSORS
SAFETY PRECAUTIONS FOR COMPRESSOR COMPONENTS
SPECIFICATIONS
FUNCTIONAL DESCRIPTION
INSTALLATION AND OPERATION
MAINTENANCE
TROUBLESHOOTING
WARRANTY
!
!
IMPORTANT SAFETY INSTRUCTIONS
READ
1. KEEP WORK AREA CLEAN. Cluttered areas invite injuries.
2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp,
3. KEEP CHILDREN AND BYSTANDERS AWAY. All children should be kept
4. GROUNDED TOOLS must be plugged into an outlet that is properly installed
and grounded. Grounding provides a low-resistance path to carry electricity
to ground away from the operator, should the tool malfunction electrically.
Do not remove the grounding prong from the plug nor alter the plug in any wa y .
If in doubt as to whether the outlet is properly grounded according to code, check
with a qualified electrician.
5. PREVENT ELECTRIC SHOCKS. Prevent body contact with grounded surfaces:
6. HANDLE THE CORD CAREFULLY. Never carry your tool by the cord or pull on
7. WHEN WORKING OUTDOORS, USE AN OUTDOOR-RATED EXTENSION
CORD. An extension cord rated for outdoor use must be marked "W-A" or "W".
8. DO NOT EXPOSE ELECTRICAL POWER TOOLS TO MOISTURE. Rain or
wet conditions can cause water to enter the tool and lead to electric shock.
9. ENSURE THE EXTENSION CORD YOU USE IS OF SUFFICIENT GAUGE
WARNING ! Read and understand all instructions. Failure to follow all
instructions listed below may result in serious personal injury.
WARNING! When using electric tools, machines or equipment, basic safety
precautions should always be followed to reduce the risk of fire, electric shock,
and personal injury. Completely read the manual before proceeding to use this tool.
KEEP THESE INSTRUCTIONS.
ALL
INSTRUCTIONS BEFORE USING THIS TOOL
wet, or poorly lit locations. Don't expose your tool to rain. Keep the work area
well lit. Don't use tools in the presence of flammable gases or liquids.
away from the work area. Don't let them handle machines, tools or extensions
cords. Visitors can be a distraction and are difficult to protect from injury.
pipes, radiators, ranges, and refrigerator enclosures. When your body is grounded
the risk of electric shock increases. When working wherever "live" electrical wires
may be encountered, try to ascertain whether there is a danger of shock. Even so,
DO NOT TOUCH ANY METAL PARTS OF THE TOOL while using it. Hold the tool
only by the plastic grip to prevent electric shock if you contact a live wire.
the cord to unplug it. Protect the cord from potential sources of damage: heat,
oil & solvents, sharp edges, or moving parts. Replace damaged cords immedi-
ately.
FOR ITS LENGTH.
Recommended Minimum Wire Gauge for Extension Cords
Amps from Tool Nameplate
25' (7 m) length 50' (15 m) length 75' (23 m) length 100' (30 m) length 150' (46 m) length 200' (61 m) length
0-5 amps
16 ga.
5.1-8 amps
16 ga.
8.1-12 amps
14 ga.
12.1-15 amps
12 ga.
15.1-20 amps
10 ga.
16 ga.
16 ga.
14 ga.
16 ga.
14 ga.
12 ga.
14 ga.
16 ga.
10 ga.
12 ga.
10 ga.
10 ga.
10 ga.
10 ga.
Do Not Use
p.12
p.14
p.15
p.17
p.17
p.18
p.18
p.18
p.21
p.22
p.23
12 ga.
12 ga.
10 ga.
Do Not Use
Do Not Use
Do Not Use
Do Not Use
Do Not Use
Do Not Use
Do Not Use
15
Publicité
Table des Matières
