Installation; General - Hatco Rapide Cuisine IRNG P Série Manuel D'installation Et D'utilisation

English
Dimensions — Built-In Models
Cooking Surface
Model
IRNG-PB1-14
IRNG-PB1-18
IRNG-PB1-36
C

General

Induction Ranges are shipped completely assembled and
ready for use. Built-in units require installation into a countertop
(see procedures in this section). Care should be taken when
unpacking the shipping carton to avoid damage to the unit and
components enclosed.
WARNING
ELECTRIC SHOCK HAZARD: Unit is not weatherproof.
Locate unit indoors where ambient air temperature is a
minimum of 70°F (21°C) and a maximum of 124°F (51°C).
FIRE HAZARD:
• Make sure to follow the installation information listed
below for specific induction ranges. If safe distances are
not maintained, discoloration or combustion could occur.
a. Locate countertop unit a minimum of 2" (51 mm)
from combustible walls and materials.
b. Locate built-in unit with a minimum of 2" (51 mm)
between front, sides, and bottom of unit and any
interior surface.
c. Locate built-in unit with a minimum of 6" (152 mm)
between back of unit and any interior surface.
• Do not obstruct air ventilation openings on sides and
bottom of unit. Unit combustion or malfunction may occur.
• Do not place unit near or underneath curtains or other
combustible materials. Items near or above unit could
catch fire causing injury and/or damage to unit.
Form No. IRNGM-1217
Cooking Surface
Width (A) Depth (B)
13-1/2ʺ 14-1/2ʺ
(343 mm) (368 mm)
13-1/2ʺ 14-1/2ʺ
(343 mm) (368 mm)
13-1/2ʺ 14-1/2ʺ
(343 mm) (368 mm)
A
E
Front View
4-9/16"
(115 mm)
Height (C) Height (D)
3ʺ
(88 mm) (72 mm)
3ʺ
(88 mm) (72 mm)
4-5/8ʺ
(117 mm) (91 mm)
D
11-15/16"
(302 mm)
Remote Control Panel
Do not block or restrict air flow to air intake or exhaust
openings on bottom of unit.
Locate unit at proper counter height in an area that is
convenient for use. Location should be level to prevent unit
or its contents from falling accidentally and strong enough
to support weight of unit and contents.
1. Remove the unit from the carton.
2. Remove tape and protective packaging from all surfaces of
the unit.
NOTE: To prevent delay in obtaining warranty coverage,
complete
IMPORTANT OWNER INFORMATION for details.
3. If the unit is a countertop model, place the unit in the
desired location. Make sure the location:
• is level and at the proper counter height.
• is strong enough to support the unit and its contents.
• provides a minimum of 2" (51 mm) clearance from
combustible materials.
• is large enough for all four feet of the unit to be positioned
securely on the countertop.
4. If the unit is a built-in model, refer to the "Installing Built-In
Models" procedure in this section.
NOTE: Avoid areas that may be subject to active air
movements or currents (i.e., near exhaust fans/hoods,
air conditioning ducts, and exterior doors).
7
SPECIFICATIONS
Unit Under-Counter
Width (E)
2-7/8ʺ 12-5/8ʺ
(320 mm)
2-7/8ʺ 12-5/8ʺ
(320 mm)
3-9/16ʺ 12-5/8ʺ
(320 mm)
B
F
SideView
2-7/16"
(62 mm)

INSTALLATION

CAUTION
online warranty
Under-Counter
Depth (F)
13-5/8ʺ
(346 mm)
13-5/8ʺ
(346 mm)
13-3/4ʺ
(349 mm)
registration. See