Before Starting The Equipment - EINHELL TE-AG 125/750 Mode D'emploi D'origine

Masquer les pouces Voir aussi pour TE-AG 125/750:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
LpA sound pressure level ................... 89,1 dB(A)
KpA uncertainty ........................................... 3 dB
LWA sound power level ................... 100,1 dB(A)
KWA uncertainty .......................................... 3 dB
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Handle:
Vibration emission value a
K uncertainty = 1.5 m/s
Additional handle:
Vibration emission value a
K uncertainty = 1.5 m/s
Additional information for electric power
tools
Warning!
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect wor-
king order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
Have the appliance serviced whenever ne-
cessary.
Switch the appliance off when it is not in use.
Wear protective gloves.
Anl_TE_AG_125_750_Kit_EX_Afrika_SPK7.indb 8
Anl_TE_AG_125_750_Kit_EX_Afrika_SPK7.indb 8
= 6.322 m/s
2
hAG
2
= 8.375 m/s
2
h
2
GB
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
5.1 Fitting the additional handle (Fig. 2)
The angle grinder must not be used without
the additional handle (3).
The additional handle can be secured in any
of three positions (A, B, C).
Tool side
Left (position A / as
shown)
Right (position B)
Top (position C)
5.2 Setting the guard (Fig. 3)
Switch off the tool. Pull the power plug.
Adjust the guard (4) to protect your hands
so that the material being ground is directed
away from your body.
The position of the guard (4) can be adjusted
to any specific working conditions. Undo the
clamp handle (a) and turn the cover (4) into
the required position.
Ensure that the guard (4) correctly covers the
gear wheel casing.
Secure the clamp handle (a) again.
Ensure that the guard (4) is secure.
- 8 -
Suitable for
Right-handed users
Left-handed users
Using cutting wheels
18.04.16 10:09
18.04.16 10:09

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

44.308.86

Table des Matières