Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Publicité
Manuels Connexes pour POWERTEX PLH-S1
Sommaire des Matières pour POWERTEX PLH-S1
- Page 1 GB Instruction for use Manuel d’utilisation POWERTEX Lever Hoist model PLH-S1...
- Page 2 POWERTEX Lever Hoist PLH-S1 0,25 – 9 ton Instruction for use (GB) (Original instructions) Read through these user instructions before using the lever hoist. Improper operation may lead to hazardous situations. General safety provisions • Check the function of the lever hoist before use. See “Daily checks” on page 3.
- Page 3 Attachment of loads Check the equipment well before use. Improper attachment of loads can be highly dangerous (see Figs. 4 a–e). Only use straps and slings of sufficient load capacity. Make sure the load is not anchored to the floor/ground or is otherwise fixed before making the lift.
- Page 4 EN 818-7 from the following manufacturers: Chaineries Limousines, Pewag, Thiele or Rud. Repairs The lever hoist must not be modified. Repairs must be carried out by specialists. Damaged parts must only be replaced with original Powertex spare parts. Order them through your dealer.
- Page 5 Checklist for periodic checks (normally yearly – more frequently if necessary) Daily Yearly Inspection items Inspection method Note Labels Rating plate Visual If the plate is hard to read - replace it Function Raising and lowering function Test without load A low snapping noise should be audible Try with 125% of rated load Raising and lowering function...
- Page 6 POWERTEX Palan à levier PLH-S1 0.25 – 9 tonnes Manuel d’utilisation (FR) Veuillez soigneusement lire ce manuel d’utilisation avant de vous servir du palan à levier. Tout maniement inapproprié peut entraîner des situa- tions dangereuses! Dispositions générales de sécurité •...
- Page 7 IMPORTANT! Aucune contrainte de flexion ne doit être appliquée au palan, aux crochets ou à la chaîne (Figs. 3b et c et Fig. 4). Fixation de charges Bien vérifier l’équipement avant utilisation. Une mauvaise fixation des charges peut être très dangereuse (voir Figs. 4 a–e). N’utiliser que des sangles et élingues de capacité...
- Page 8 Réparations Le palan à levier ne doit pas être modifié. Les réparations doivent être effectuées par des spécialistes. Les pièces endommagées doivent unique- ment être remplacées par des pièces de rechange Powertex originales. Les commander par l’intermédiaire de votre distributeur.
- Page 9 Liste de vérifications pour les inspections périodiques (généralement annuelles – plus fréquentes si nécessaire) Tous les Tous les Objets des inspections Méthode d’inspection Remarque jours Étiquettes Si la plaque est difficile à lire, la remplacer Plaque signalétique Visuelle Fonctionnement Fonction de levage et descente Essai sans charge On doit entendre un petit claquement sec Fonction de levage et descente Essai avec 125% du poids Le levier fonctionne facilement.
- Page 10 POWERTEX Lever Hoist PLH-S1 – Spare parts 0,25 t When ordering spare parts, specify model, WLL, part number and the quantity needed. When ordering chain, also specify lifting height. If the load chain has been damaged or worn out the load sheave probably has to be replaced.
- Page 11 Spare parts list 0,25 t Description 0,25 t 16.20PLH1511001 Gear cover 16.20PLH1511003 Drive shaft 16.20PLH1511004 Splined gear 16.20PLH1511005 Right side plate assy 16.20PLH1511006 Load chain sprocket 16.20PLH1511007 Bushing 16.20PLH1511008 Stay bolt B 16.20PLH1511009 Pin for tophook 16.20PLH1511010 Bushing B 16.20PLH1511011 Chain stripper 16.20PLH1511012 Stay bolt A...
- Page 12 POWERTEX Lever Hoist PLH-S1 – Spare parts 0,5 – 6 t When ordering spare parts, specify model, WLL, part number and the quantity needed. When ordering chain, also specify lifting height. If the load chain has been damaged or worn out the load sheave probably has to be replaced.
- Page 13 Spare parts list 0,5 – 6 t Description 0,5 t 1,5 t 16.20PLH1512001 16.20PLH1514001 16.20PLH1515001 16.20PLH1517001 16.20PLH1520001 Gear cover assy 16.20PLH1512002 16.20PLH1514002 16.20PLH1515002 16.20PLH1517002 16.20PLH1520002 Disc gear assy 16.20PLH1512003 16.20PLH1514003 16.20PLH1515003 16.20PLH1517003 16.20PLH1520003 Drive shaft 16.20PLH1512004 16.20PLH1514004 16.20PLH1515004 16.20PLH1517004 16.20PLH1520004 Splined gear 16.20PLH1512005 16.20PLH1514005...
- Page 14 POWERTEX Lever Hoist PLH-S1 – Spare parts 9 t When ordering spare parts, specify model, WLL, part number and the quantity needed. When ordering chain, also specify lifting height. If the load chain has been damaged or worn out the load sheave probably has to be replaced.
- Page 15 Spare parts list 9 t Pos Description Hook shaft 16.20PLH1522001 Gear cover assy Beam for hook connector- Left 16.20PLH1522002 Disc gear assy Stay bolt A 16.20PLH1522003 Drive shaft Short stay bolt 16.20PLH1522004 Splined gear Stay bolt B 16.20PLH1522005 Right side plate assy Hanger plate 16.20PLH1522006 Load chain sprocket...
- Page 16 SVERO AB Momarken 19 9556 50 Jönköping Sweden...
- Page 17 Standard: EN 13157 Warning tag The warning tag shows some specific and important situations, in which you must pay special attention, when using POWERTEX Chain Blocks and Lever Hoists. User Manuals You can always find the valid and updated User Manuals on the web.
- Page 18 www.powertex-products.com...