EINHELL TE-HP 140 Mode D'emploi D'origine page 21

5. Before starting the equipment
It is recommend for the power supply to this ma-
chine either to be connected via a residual current
device circuit-breaker, which interrupts the power
fl ow as soon as the leakage current to earth ex-
ceeds 30 mA for 30 ms, or for it to be equipped
with an earth tester.
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
5.1 Using the equipment correctly
•
The pressure cleaner must be stood on a le-
vel, stable surface.
•
It is recommended that you adopt the correct
operating position every time you use the
equipment, with one hand on the gun and the
other on the lance.
•
Never direct the water jet at electrical lines or
the equipment itself.
•
So that the pump does not suffer any damage
when it is not in use, a small amount of leaka-
ge from the pump is normal.
•
Never use the machine in potentially explosi-
ve areas under any circumstances!
•
The operating temperature must be between
+5 and + 40°C.
•
Do not cover or modify the lance or the spray
nozzles in any way.
•
The pressure cleaner is designed to be used
with cold or lukewarm water (max. 40 °C); hig-
her temperatures can damage the pump.
•
Do not use water that is dirty, gritty or con-
tains any chemical products, as these could
impair operation and shorten the life of the
equipment.
Caution: Risk of explosion
Do not spray fl ammable liquids.
Warning
Water that has passed through the non-return
valve is not drinkable.
Anl_TE_HP_140_SPK9.indb 21 Anl_TE_HP_140_SPK9.indb 21
GB
Warning
If cleaning agent gets into contact with your skin
or into your eye, rinse immediately with lots of
clean water. Then consult a doctor or follow the
steps described on the safety data sheet or provi-
ded by the manufacturer of the cleaning agent.
5.2 Assembly
5.2.1 Assembling the equipment (Fig. 4a-4g)
Assemble the pressure cleaner as shown in Figu-
re 4a-4g.
Note! Before using the pressure cleaner, make
sure that the high-pressure hose is completely
unwound.
5.2.2 Fitting the gun attachments (Fig. 3)
Various attachments can be fi tted to the gun. To
do so, press the attachment into the gun (you will
encounter a slight spring resistance) and secure
the attachment by turning.
Important! Check that the attachment is secure
before you begin with the cleaning.
Lance with rotating nozzle (15)
To remove particularly stubborn dirt, use the lance
with the rotating nozzle (15).
Solid cone / fl at fan lance (7)
The shape of the water jet can be changed from
solid cone to fl at fan by turning nozzle (a) (Fig.
8). To switch to low/high pressure, turn nozzle (b)
(Fig. 8).
Washing brush (13)
The washing brush (13) is intended for (low pres-
sure) cleaning with cleaning agent.
Terrace cleaner (19)
To use the terrace cleaner, fi t the extension (6)
between the gun (5) and the terrace cleaner (19)
(Fig. 9).
Foam nozzle (17)
You can adjust the quantity of cleaning agent you
want to add by turning the setting wheel (20). We
recommend using the cleaning agent sparingly.
5.2.3 Assembling the terrace cleaner
(Fig. 5a-5d)
Assemble the terrace cleaner as shown in Fig.
5a-5d.
- 21 -
12.05.2020 13:21:37 12.05.2020 13:21:37