Publicité
Les langues disponibles
Les langues disponibles
12.
Repairs
Repairs to electrical tools must be carried out
by qualified electricians ONLY!
If the connection lead is damaged, it must be
replaced by a special connection lead.
Contact your local WOLFF representative if you
have WOLFF power tools requiring repairs.
You can download a list of spare parts from
www.wolff-tools.com.
Always have your guard repaired by qualified
personnel only using genuine spare parts.
This will ensure that the safety of the guard is
maintained.
13.
Environmental Protection
The generated grinding dust may contain harmful
substances. Dispose appropriately.
Observe national regulations on environmentally
compatible disposal and on the recycling of
disused machines, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Directive
2002/96/EC relating to electrical and electronic
waste and
implementation of national law, used electrical
tools must be collected separately and disposed of
in an environmentally friendly manner at recycling
centres.
14.
Technical Specifications
Changes due to technological progress reserved.
Ø
= max. diameter of the accessory ..................... 125 mm
t
max,1 = max. permitted thickness of the
clamping shank on accessory when
using 2-hole nut (13) .................................... 10,0 mm
t
max,2 = max. permitted thickness of clamping
shank on accessory when using-
"Quick" clamping nut (1) ................................. 6,8 mm
max,3 = roughing disc/cutting disc::
t
max. permitted thickness of accessory ........... 6,8 mm
M
= Spindle thread ..................................................... M 14
l
= length of the grinding spindle ........................... 20 mm
n*
= no-load speed (maximum speed) ................ 11.000 U
P1
rated input power .............................................1550W
P2
= power output.......................................................940W
m
= Weight without main cable ................................ 2,5 kg
14.1 Come with
Concrete grinding BS 125
with safety cover
Diamond grinding disc
Hearing protection #15315
Bar side handle
#80480
Safety gloves
#15316
Carrying case
#74844
Twin hole spanner #14960
Manual
#80720
Spare parts list
#80721
Measured values determined in conformity with
EN 60745.
Machine in protection class II
~ AC Power
*Machines with the designation BS 125:
Energy-rich, high-frequency interference can
cause fluctuations in speed. The fluctuations
disappear, however, as soon as the interference
fades away.
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. Depending on the operating
conditions, the condition of the power tool or the
accessories, the actual load may be higher or
lower.
For assessment purposes, please allow for breaks
and periods when the load is lower. Based on the
adjusted estimates, arrange protective measures
for the user e.g. organisational measures.
Vibration total value(vector sum of three directions)
determined in accordance with EN 60745:
a
= Vibration emission value
h, SG
(surface grinding)
a
= Vibration emission value
h, DS
((sanding with sanding plate)
K
= Uncertainty (vibration)
h,SG/DS/P
Typical A-effective perceived sound levels:
L
= Sound-pressure level 93,0 dB(A)
pA
L
= Acoustic power level
WA
K
, K
= Uncertainty
pA
WA
During operation the noise level
can exceed.
Wear ear protectors!
#80582
#72983
2
6,0 m/s
3,6 m/s
2
2
1,5 m/s
104,0 dB(A)
93,0 dB(A)
80,0 dB(A)
- 18 -
Publicité
