Electrolux EKM3 Série Mode D'emploi page 7

release button. The attachment release button will click into position once the meat grinder is securely attached.
Place a container under the attachment
Caution: Before attaching accessories turn off the appliance and unplug it.
11
Place the food tray over the grinder housing. Cut raw meat into small pieces and place it on the food tray.
Plug in the appliance and turn the speed selector to desired speed (recommended speed: 3-4). Feed the meat
into the feed chute by using the pusher.
Caution: Do not put your fingers or other utensils in the feed chute.
Note: Meat should not contain bones, muscles or skin.
HOW TO USE THE SLICER/SHREDDER*
12 Choose a cylindrical slicer (medium or course) or a shredder knife. Insert the attachment by turning it clock-
wise into the slicer/shredder housing. Make sure the attachment is fully inserted.
Caution: The blades and inserts are very sharp!
13
Push down the release button for the front attachment hub to the right and remove the attachment hub
cover. Fit the power shaft of the attachment in the front attachment hub socket, using the attachment hub
release button. Assemble the slicer/shredder in the attachment hub. The attachment release button will click
into position once the slicer/shedder is securely attached. Place a container under the attachment.
Cut the food into small pieces. Plug in the appliance and turn the speed selector to desired speed
(recommended speed: 5).
14 Feed the food into the feed chute by using the pusher. When finished using your attachment, turn off the
appliance and unplug it. Place the front attachment hub cover using the attachment hub release button.
HOW TO USE THE BLENDER*
15
Remove the rear attachment hub cover by pulling it straight backwards. Place the bottom of the blender on
the three rubber rings. Align the arrows on the blender to the arrows on the main body.
Caution: Turn off and unplug the appliance before attaching any accessories.
16
Rotate the blender clockwise to lock it in position. The blender handle should point towards the back of the
machine when properly fixed. Place the blender lid and measuring cup. Insert the plug in the main socket.
Adjust the speed selector to the desired speed (recommended speed: 6), mix until the right consistency of the
blend is reached.
Caution: Never operate blender without ingredients.
CLEANING AND CARE
17
Unplug the appliance. The wire whip, meat grinder* and slicer/shredder* should only be washed by hand in
warm soapy water.
The bowl, flat beater and dough hook are dishwasher-proof. Only place parts on the top rack if using a
dishwasher.
Caution! The blades and inserts are very sharp and can cause injury.
Warning! Never immerse the housing, plug, or cord in water or any other fluid.
Dry each part thoroughly before use.
18
Cleaning the blender*:
Rotate the blender counter-clockwise and remove. Take off the lid. Pour out the mixture from the blender.
Add a drop of dishwashing soap and one litre of warm water. Fix the blender on the appliance.
Run the machine on speed 6 for half a minute, then pour out the water. Rinse the blender and let it dry.
Caution! The blades and inserts are very sharp and can cause injury.
19
The housing should only be cleaned with a soft damp cloth, then dried with a cloth.
Note: Do not use abrasive cleansers or scouring pads to clean the surfaces of your appliance.
Enjoy your new Electrolux product!
www.electrolux.com
EKM3xxx_Kitchen Machine_Electrlx.indd 7
GB
FR
AR
BG
CZ
DE
DK
EE
ES
FA
FI
GR
HR
HU
IT
LT
LV
NO
PL
RO
RS
RU
SE
SI
SK
TR
UA
7
2017-05-24 16:08:30