Cycle Defaults Table; Start-Up - Omnifilter OM34K Instructions D'installation

Figure 17

CYCLE DEFAULTS TABLE

OM34K Recharge Cycles:
Table 1 Length of Cycle
Cycle Cycle HE
Description Setting
1 Backwash 1 10 min
2 Brine Draw
54 min
Slow Rinse
3 Re- 3 min
Pressurize
4 Fast Rinse 1 4 min
5 Backwash 2 1 min
6 Fast Rinse 2 1 min
7 Refill 3 .5 min
*The camshaft does not move between Brine Draw and Slow Rinse.
Slow Rinse begins when the brine in the salt tank runs out and the
check valve closes.
OM40K Recharge Cycles:
Table 1 Length of Cycle
Cycle Cycle HE
Description Setting
1 Backwash 1 10 min
2 Brine Draw
51 min
Slow Rinse
3 Re- 3 min
Pressurize
4 Fast Rinse 1 4 min
5 Backwash 2 1 min
6 Fast Rinse 2 1 min
7 Refill 4 .1min
*The camshaft does not move between Brine Draw and Slow Rinse.
Slow Rinse begins when the brine in the salt tank runs out and the
check valve closes.
OM34K Recharge Cycle Requirements:
Minimum Salt/
Salt/Recharge (lbs)
Regeneration Time
(min)
Water to Drain (gal)
Max . Flow to Drain
(gpm)
OM40K Recharge Cycle Requirements:
Minimum Salt/
Salt/Recharge (lbs)
Time remaining to
end of cycle
HC HE
Setting Setting
10 min 76 .5 min
82 min 66 .5 min
3 min 12 .5 min 25 .5 min
4 min 9 .5 min 22 .5 min
1 min 5 .5 min 18 .5 min
1 min 4 .5 min 17 .5 min
16 .5 min 3 .5 min 16 .5 min
Time remaining to
end of cycle
HC HE
Setting Setting
10 min 74 .1 min 118 .1 min
79 min 64 .1 min 108 .1 min
3 min 13 .1 min 29 .1 min
4 min 10 .1 min 26 .1 min
1 min 6 .1 min 22 .1 min
1 min 5 .1 min 21 .1 min
20 .1 min 4 .1 min 20 .1 min
Maximum Salt/
Capacity Capacity
3 .4 16 .7
76 .5 117 .5
46 .3 56 .9
2 .1 2 .1
Maximum Salt/
Capacity Capacity
4 .1 20
Regeneration Time
(min)
Water to Drain (gal)
Max . Flow to Drain
(gpm)

START-UP

HC
The conditioner will now need to be placed into operation .
Setting
Please review Quick Cycling the Control procedure before
117 .5
attempting start-up .
min
DO NOT put regenerant material into the brine tank .
107 .5
1 . With the supply water for the system still turned off, position
min
the bypass valve to the "not in bypass" (normal operation)
position .
Both valve
handles pointing
in direction of
water flow
2 . Press and hold the
HC
seconds. This will initiate a manual regeneration, and cycle
Setting
to the backwash position .
3 . Filling the media tank with water .
A . With the conditioner in backwash, open the water
supply valve very slowly to approximately the 1/4 open
position . Water will begin to enter the media tank . Air
will begin to be purged to drain as the media tank fills
with water .
WARNING:
B . When all of the air has been purged from the media
tank (water begins to flow steadily from the drain line),
open the main supply valve all of the way. This will
purge the final air from the tank.
C . Allow water to run to drain until the water runs clear
from the drain line . This purges any debris from the
media bed .
D . Pour about 3 gallons of water into the brine tank .
Advance to cycle 2 (Brine Draw) by pressing the
and
tank should be drawn into the valve. If the water is not
receding from the tank, refer to Troubleshooting.
E . Quickly cycle the control to the refill cycle (C7). Place
salt in brine tank. Allow this cycle to finish and the
control to move to service. The brine tank will have the
correct amount of water .
WARNING:
The water conditioning system is now fully operational.
The display will show the hour of the day . The decimal point at
bottom center of the display will blink when water is flowing.
74 .1
58 .7
2 .7
button on the controller for 3
If opened too rapidly or too far, media may
be lost out of the tank into the valve or the
plumbing. In the 1/4 open position, you
should hear air slowly escaping from the
valve drain line.
buttons at the same time . The water in the brine
Ensure that the system has been properly
disinfected per the water conditioning
system manufacturer's recommendations.
OM34K and OM40K OC11 • 11
118 .1
72 .1
2 .7