Télécharger Imprimer la page

EINHELL RT-ID 75/1 Mode D'emploi D'origine page 16

Masquer les pouces Voir aussi pour RT-ID 75/1:

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 18
Anleitung_RT_ID_75_1_SPK1:_
GB
Tip: Start drilling holes at low speed. Then increase
the speed in stages.
Benefits:
The drill bit is easier to control when starting the
hole and will not slide away.
You avoid drilling messy holes (for example in
tiles).
6.3 Clockwise/Counter-clockwise switch
(Fig. 11/Item 7)
Change switch position only when the drill is
at a standstill!
Switch the direction of the hammer drill using the
clockwise/counter-clockwise switch (7):
Direction
Clockwise (forwards and drill) Pushed in to the right
Counter-clockwise (reverse)
6.4 Drill / hammer drill selector switch
(Fig. 12/Item 3)
Change switch position only when the drill is at a
standstill!
Drill
Drill / hammer drill selector switch (3) in the drill
position. (Position A)
Use for: Wood, metal, plastic
Hammer drill
Drill / hammer drill selector switch (3) in the hammer
drill position. (Position B)
Use for: Concrete, rock, masonry
6.5 Drilling with the dust extraction system (9)
Use the dust extraction system only for drilling into
concrete, bricks and masonry since wood or plastic
chips may block the extraction system. Do not drill
into metallic materials since hot metal chips can
damage the dust extraction system.
Fit the dust extraction system (9); see point 5.3.
Connect the dust extractor adapter (10) to the
suction hose of a suitable vacuum cleaner. The
vacuum cleaner must be suitable for handling the
substance that will be extracted. Harmful dust
must not be extracted using the dust extraction
system (9). Use on materials containing
asbestos is prohibited!
Set the required drilling depth (see point 5.2).
Mark the drilling position.
16
19.01.2011
13:25 Uhr
Tip: To prevent the wall being soiled, you can
mask the area around the transparent extraction
opening with masking tape. Before you use the
masking tape, test whether the tape can be
removed easily from the wall again in a place
that it not easily visible.
Switch on the vacuum cleaner and place the
transparent cover on the front of the dust
extraction system (9) over the drilling point so
that the drill bit is in front of the mark. Ensure that
the transparent cover is in contact with the
workpiece or wall.
Press the drill bit and machine gently against the
mark whilst the ON/OFF switch (5) is still set to
off.
Then drill the hole. See the instructions in point
Switch position
6.6 for more details.
The dust extraction system (9) must be cleaned
after at least every 15 holes. For this purpose
Pushed in to the left
remove the dust extraction system (9) and the
additional handle (8) as described in points 5.3
and 5.1. Clean the dust extraction system (9)
and the interior of the additional handle (8) by
carefully tapping them or blowing them through
with low pressure compressed air.
If the extraction performance is poor, check the
dust extraction system (9) for possible blockages
or dirt.
The transparent cover is enclosed in a protective
ring to prevent it from suffering damage. This
protective ring should be replaced as soon as it
is damaged or worn.
6.6 Tips for working with your hammer drill
6.6.1 Drilling concrete and masonry
Switch the Drill/Hammer drill selector switch (3)
to position B (Hammer drill).
Always use carbide drill bits and a high speed
setting for drilling into masonry and concrete.
6.6.2 Drilling steel
Switch the drill / hammer drill selector switch (3)
to position A (drill).
Always use HSS drill bits (HSS = high speed
steel) and a low speed setting for drilling steel.
We recommend that you lubricate the hole with a
suitable cutting fluid to prevent unnecessary drill
bit wear.
6.6.3 Starting holes
If you wish to drill a deep hole in a hard material
(such as steel), we recommend that you start the
hole with a smaller drill bit.
Seite 16

Publicité

loading

Ce manuel est également adapté pour:

42.597.47