JVC KD-X350BTS Manuel D'instructions page 28

AUDIO SETTINGS
PRO EQ Adjust your own sound settings.
• The settings are stored to [USER].
• The settings made may affect the current settings of [EASY EQ].
62.5HZ
LEVEL –09 to LEVEL +09 (LEVEL 00): Adjusts the level to memorize for each source.
(Before making an adjustment, select the source you want to adjust.)
ON: Turns on the extended bass. ; OFF: Cancels.
100HZ/160HZ/250HZ/400HZ/630HZ/1KHZ/1.6KHZ/2.5KHZ/4KHZ/6.3KHZ/10KHZ/
16kHZ
LEVEL –09 to LEVEL +09 (LEVEL 00): Adjusts the level to memorize for each source.
(Before making an adjustment, select the source you want to adjust.)
Q FACTOR 1.35/1.50/2.00: Adjust the quality factor.
AUDIO CONTROL
BASS BOOST LEVEL +01 to LEVEL +05: Selects your preferred bass boost level. ;
OFF: Cancels.
LOUDNESS LEVEL 01/LEVEL 02: Boosts low or high frequencies to produce a well-
balanced sound at low volume. ; OFF: Cancels
SUB.W LEVEL * 1 SPK-OUT * 2
PRE-OUT * 3
SUBWOOFER ON: Turns on the subwoofer output. ; OFF: Cancels.
SET *
3
FADER (Not applicable when 3-way crossover is selected.)
POSITION R15 to POSITION F15 (POSITION 00): Adjusts the front and
rear speaker output balance.
24
ENGLISH
(Not applicable when 3-way crossover is selected.)
SUB.W 00 to SUB.W +06 (SUB.W +03): Adjusts
the output level of the subwoofer connected via
speaker lead. ( 39)
SUB.W –50 to SUB.W +10 (SUB.W 00): Adjusts
the output level of the subwoofer connected to
the lineout terminals (SW or REAR/SW) through an
external amplifier. ( 40)
BALANCE * 4
POSITION L15 to POSITION R15 (POSITION 00): Adjusts the left and
right speaker output balance.
VOLUME ADJUST LEVEL –15 to LEVEL +06 (LEVEL 00): Preset the initial volume level
of each source (compared to the FM volume level). Before adjustment,
select the source you want to adjust.
AMP GAIN LOW POWER: Limits the maximum volume level to 25. (Select if
the maximum power of each speaker is less than 50 W to prevent
damaging the speakers.) ; HIGH POWER: The maximum volume level
is 35.
SPK/PRE OUT (Not applicable when 3-way crossover is selected.)
Depending on the speaker connection method, select the appropriate
setting to get the desired output. ( 25, Speaker output settings)
SPEAKER SIZE Depending on the crossover type you have selected ( [X ' OVER
TYPE]), 2-way crossover or 3-way crossover setting items will be
shown. ( 26, Crossover settings)
X ' OVER
By default, 2-way crossover type is selected.
DTA SETTINGS
For settings, 27, Digital Time Alignment settings.
CAR SETTINGS
X ' OVER TYPE Caution: Adjust the volume before changing the [X ' OVER TYPE] to
avoid the sudden increase or decrease of the output level.
2-WAY (Displayed only when [3-WAY] is selected)
YES: Selects two way crossover type. ; NO: Cancels.
3-WAY (Displayed only when [2-WAY] is selected)
YES: Selects three way crossover type. ; NO: Cancels.
*
1
Displayed only when [SUBWOOFER SET] is set to [ON].
*
2
For 2-way crossover: Displayed only when [SPK/PRE OUT] is set to [SUB.W/SUB.W].
( 25)
*
3
For 2-way crossover: Displayed only when [SPK/PRE OUT] is set to [REAR/SUB.W] or
[SUB.W/SUB.W]. ( 25)
*
4
This adjustment will not affect the subwoofer output.