Before Use - Hilti SF 10W-A22 Mode D'emploi

Printed: 03.09.2015 | Doc-Nr: PUB / 5161651 / 000 / 05
Printed: 17.07.2019 | Doc-Nr: PUB / 5161651 / 000 / 06
NOTE
The sound pressure and vibration values given in these instructions have been measured in accordance with a
standardized test and may be used to compare one electric tool with another. They may be used for a preliminary
assessment of exposure. The data given represents the main applications of the electric tool. However, if the electric
tool is used for different applications, with different accessories or is poorly maintained, the data may vary. This may
significantly increase exposure over the total working period. An accurate estimation of exposure should also take into
account the times when the tool is switched off, or when it is running but not actually being used for a job. This may
significantly reduce exposure over the total working period. Identify additional safety measures to protect the operator
en
from the effects of noise and/or vibration, for example: maintain the electric tool and accessories, keep the hands
warm, organisation of work patterns.
Noise information in accordance with EN 60745:
Sound power level for the SF 10W-A22, L
WA
Sound power level for the SF 8M‑A22, L
WA
Uncertainty for the given sound power level, K
Emission sound pressure level for the SF 10W‑A22, L
Emission sound pressure level for the SF 8M‑A22, L
Uncertainty for the given sound power level, K
Total vibration (vector sum of three directions), determined in accordance with EN 60745:
Vibration emission value for screwdriving, a
Uncertainty for screwdriving, K
h
Vibration emission value for drilling in metal, a
Uncertainty for drilling in metal, K
h,D
Battery B 22/1.6 Li‑Ion
Rated voltage 21.6 V
Capacity 1.6 Ah
Weight 0.48 kg

5 Before use

5.1 Charging a previously used battery
Ensure that the outer surfaces of the battery are clean
and dry before inserting the battery in the corresponding
charger.
Read the operating instructions for the charger for further
information about the charging procedure.
5.2 Inserting the battery
CAUTION
Before fitting the battery, check that the power tool
is switched off and that the safety lock is engaged
(forward/reverse switch in the middle position). Use
only the Hilti batteries approved for use with this
power tool.
1. Push the battery into the tool from the rear as far as
it will go and until it is heard to engage with a double
click.
2. CAUTION A falling battery may present a risk of
injury to yourself and others.
Check that the battery is securely seated in the tool.
16
86 dB (A)
88 dB (A)
3 dB (A)
WA
75 dB (A)
pA
77 dB (A)
pA
3 dB (A)
pa
< 2.5 m/s²
h
1.5 m/s²
< 2.5 m/s²
h,D
1.5 m/s²
B 22/2.6 Li‑Ion (02) B 22/3.3 Li‑Ion B 22/5.2 Li‑Ion
21.6 V 21.6 V 21.6 V
2.6 Ah 3.3 Ah 5.2 Ah
0.48 kg 0.78 kg 0.78 kg
5.3 Removing the battery 2
5.4 Fitting the side handle 3
1. Set the forward / reverse switch to the middle pos-
ition (transport lock) or remove the battery from the
power tool.
2. Release the side handle clamping band by turning
the handle counterclockwise.
3. Slide the side handle clamping band over the chuck
and onto the clamping section at the front end of
the power tool.
4. Pivot the side handle into the desired position.
5. Secure the side handle by turning the handle clock-
wise.
6. Check that the side handle holds securely.
5.5 Transport and storage of batteries
CAUTION
Fire hazard. Never transport batteries in loose, bulk form.
There is a risk of short circuiting.