Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
5. Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Always
unplug the charger from the power supply when there
is no battery pack in the cavity. Unplug the charger
before attempting to clean.
6. Do not freeze or immerse the charger in water or any
other liquid.
Storage Recommendations
1. The best storage place is one that is cool and dry, away
from direct sunlight and excess heat or cold.
2. For long storage, it is recommended to store a fully
charged battery pack in a cool dry place out of the
charger for optimal results.
nOTE: Battery packs should not be stored completely
depleted of charge. The battery pack will need to be
recharged before use.
SAVE THESE INSTRUCTIONS
FOR FUTURE USE
COMPONENTS (FIG. A)
WARNING:
tool or any part of it. Damage or personal injury could result.
Refer to Figure A at the beginning of this manual for a
complete list of components.
INTENDED USE
This appliance is designed for professional outdoor
blower applications.
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
This appliance is a professional power tool. DO nOT let
children come into contact with the tool. Supervision is
required when inexperienced operators use this tool.
ASSEMBLY AND ADJUSTMENTS
WARNING:
of serious personal injury, turn unit off and remove
the battery pack before making any adjustments or
removing/installing attachments or accessories. An
accidental start-up can cause injury.
CAUTION:
3
is in the locked position to prevent the trigger switch
from moving and the battery pack
attaching or removing the tube
to the housing
11
before use.
1. TUBE AssEMBlY: To attach the tube to the blower,
line up the pegs
12
the notch
13
on the bottom of the housing opening
as shown in figure C. Push the tube into the blower
housing until the lock engages the tube.
Never modify the power
To reduce the risk
Ensure the lock-off switch
7
is removed before
5
. The tube must be attached
on the bottom of the tube with
2. Pull on the tube to ensure it is securely in place.
3. To remove the tube, insert a screwdriver into the
unlocking hole
tab inside and pull tube out.
fig. C
Attaching Nozzles (Fig. D)
1. Line up the channels
with the nubs
2. Slide the nozzle onto the tube.
3. Firmly twist the nozzle to lock the nubs completely into the
recess of the nozzle. Ensure the nozzle is securely attached.
fig. D
OPERATION
WARNING:
of serious personal injury, turn unit off and remove
the battery pack before making any adjustments or
removing/installing attachments or accessories. An
accidental start-up can cause injury.
WARNING:
without tube securely in place. Never reach down into housing
through tube hole.
WARNING:
switch to the locked position and remove the battery when:
ʵ You leave blower unattended.
ʵ Checking, adjusting, cleaning, or working on blower.
Installing and Removing the Battery Pack
(Fig. E, F)
nOTE: For best results, make sure your battery pack is
fully charged.
1
WARNING:
installing battery, make certain the lock-off switch
locked position to prevent switch actuation.
To install battery pack: Insert battery pack
housing
6
as shown in figure E until fully seated and an
audible click is heard. Make sure battery pack is fully seated
and fully latched into position.
on the side of the housing. Lift the
14
11
13
12
14
15
of the desired nozzle
16
on the tube
5
.
16
To reduce the risk
Do not operate blower
Always slide the lock-off
Before removing or
English
9
or
10
15
9
is in the
3
7
into battery
7
Publicité
Table des Matières
