Qlima Diandra 50 S-line Manuel D'utilisation page 157

ECONO
TURBO
ECONO SEND
TURBO
AUTO
ON 1
ON 2 CANCEL
ECONO SEND
TURBO
ON 1 AUTO
ON 2 CANCEL
ECONO
TURBO
4.
ECONO
TURBO
ECONO SEND
TURBO
ON 1 AUTO
OFF 1
ON 2 CANCEL OFF 2
ECONO SEND
ECONO: Use this button to activate/deactivate the ECONO mode. Hold the
TURBO
button down for at least 2 seconds to activate/deactivate this mode.
ECONO SEND
AUTO
ON 1
OFF 1
TURBO
TURBO: Use this button to activate/deactivate the TURBO mode. Hold the
ON 2 CANCEL OFF 2
AUTO
ON 1 OFF 1
button down for at least 2 seconds to activate/deactivate this mode.
SEND
ON 2 CANCEL OFF 2
CLOCK: To set the clock mode on the remote control, proceed as follows:
ECONO SEND
AUTO
ON 1
OFF 1
1. Press
TURBO
AUTO
ON 1 OFF 1
2. The symbol appears and the time flashes.
ON 2 CANCEL OFF 2
ON 2 CANCEL OFF 2
ECONO SEND
3. Use the buttons to set the hours and minutes.
ECONO SEND
TURBO
ECONO SEND
AUTO
ON 1 OFF 1
4. Press the TURBO
CANCEL
ON 2 OFF 2
TURBO
AUTO
ON 1
CANCEL
ON 2
ON 1 AUTO
OFF 1
ON1: Use this button to set a schedule for switching the stove on automati-
ON 2 CANCEL OFF 2
cally (programme 1).
ECONO SEND
OFF 1
OFF1: Use this button to set a schedule for switching the stove off automati-
TURBO
OFF 2
cally (programme 1).
ON 1 AUTO
OFF 1
ON 2 CANCEL OFF 2
ON2: Use this button to set a schedule for switching the stove on automati-
cally (programme 2).
OFF 1
OFF 2
OFF2: Use this button to set a schedule for switching the stove off automati-
SEND
cally (programme 2).
AUTO
ON 1 OFF 1
AUTO: Use this button to repeat the set timer programmes (1 and 2) dai-
SEND
CANCEL
ON 2 OFF 2
ly. Hold the button down for at least 2 seconds to activate/deactivate this
mode. The display shows AUTO.
ON 1 AUTO
OFF 1
ON 2 CANCEL OFF 2
CANCEL: Use this button to cancel the programmed switch-on or switch-off
times.
SETTING THE TEMPERATURE
ECONO SEND
Use the and
TURBO
ECONO SEND
40ºC). When the desired temperature has been selected, press ON 1 AUTO
OFF 1
TURBO
ON 2 CANCEL OFF 2
AUTO
ON 1 OFF 1
ON 2 CANCEL OFF 2
SETTING THE HEAT OUTPUT
Use the button (1) to select the desired heat output setting. Then push
ECONO SEND
(3). The text on1-on2-on3-on4 or on5 will appear on the stove. The power (2) will
TURBO
also be shown on the remote control. You can also select Auto mode. See figure 6.
AUTO
ON 1 OFF 1
ON 2 CANCEL OFF 2
AUTO MODE
In this mode, the stove uses the difference between the desired temperature and
the room temperature itself to calculate the required output. To select auto mode,
press (1) until the
ECONO SEND
end auto mode, press
TURBO
(2). See figure 7.
ECONO SEND
ON 1 AUTO
OFF 1
TURBO
ON 2 CANCEL OFF 2
ON 1 AUTO
OFF 1
ON 2 CANCEL OFF 2
again to confirm and press
ECONO
OFF 1
TURBO
OFF 2
buttons (1&2) to set the desired temperature (from 7ºC to
symbol appears. Press
ECONO
TURBO
(1) again, select the desired output and confirm with
ON 1
ECONO SEND
ON 2
TURBO
ON 1 AUTO
OFF 1
ON 2 CANCEL OFF 2
.
SEND
AUTO
ON 1 OFF 1
ON 2 CANCEL OFF 2
(3). See figure 5.
ECONO SEND
TURBO
ON 1 AUTO
OFF 1
ON 2 CANCEL OFF 2
(2) to confirm your choice. To
SEND
AUTO
OFF 1
CANCEL OFF 2
4
157
ECONO SEND
TURBO
ON 1 AUTO OFF 1
ON 2 CANCEL OFF 2