Publicité
Les langues disponibles
Les langues disponibles
Intended use
This product is intended to illuminate persons and objects in a
dry environment.
Always follow the safety information.
Any usage other than described above is not permitted and can
damage the product and lead to associated risks such as short-
circuit, fire, electric shock, etc. You are not allowed to modify the
product.
This product fulfills legal requirements.
General Notes
•
The SkyPanel soft lights are intended for professional use
and may only be operated by qualified persons.
•
Please read these instructions carefully before using the
product for the first time. The following text contains import-
ant information for safe handling.
•
For your personal safety, please observe the safety
instructions and warnings given here and in the Safety and
Installation manual (L5.0016680). The manual is available
for download free of charge on the website www.arri.com.
•
Observe all common and local safety regulations.
•
Please keep these instructions for possible subsequent
owners.
•
Please dispose the packing material at your local recycling
center for environmental protection.
•
Defective products shall be disposed appropriately. For fur-
ther information please ask your ARRI dealer or your local
authorities.
•
Use only original ARRI spare parts and accessories.
Safety Instruction
DANGER OF LIFE – MAINS VOLTAGE!
•
Do not open the housing of the SkyPanel and the power
supply. For safe operation, the housing must be completely
closed at all times.
•
Always earth the fixture electrically. Only use TN- or TT one
phase power supplies and a power plug according to IEC
60309-1 or a similar national standard.
•
Use only genuine ARRI Power supply units (PSU) and
connector cables designed for the SkyPanel. The use of
third-party power supply units and connector cables void
the warranty.
•
Do not use any cable to hold, move or suspend the fixture
or the power supply unit.
•
Check the mains cable and connector cables prior to every
operation for damage.
•
You must not connect or disconnect the connector cable
when the power supply unit is powered.
•
In case of visible damage to cables or housings, the device
may not be operated any longer. Damaged components of
the housing must be replaced by an ARRI service center.
CAUTION – HIGH BEAM INTENSITY!
Do not look into the active light source of the
SkyPanel.
Always observe the minimum distance to persons and
flammable objects given on the type plate.
Warnings
•
Do not cover the ventilation slots of the fixture or the power
supply unit. Unobstructed airflow is required for effective
cooling.
•
Avoid direct illumination by other fixtures or other heat
sources.
To Secure the Fixture and its Accessories
•
When mounted in a hanging position or above persons, use
a suitable safety cable to prevent the SkyPanel and the
attached accessories against falling when the primary
mounting method fails.
•
The safety cable and its connecting elements must be rated
at a minimum load of 10 times the weight of the device and
all attached accessories.
•
Lead the safety cable
• Carbon fiber yoke: Around the Yoke and through the safe-
ty loop attachment (version 1 and 2), or
• Short yoke: Around the yoke and through the safety loop
attachment (version 3)
and the structure the fixture is mounted to.
•
The safety cable must be kept short.
•
Both locking pins (A) must snap in the guide holes of the
diffuser / intensifier firmly.
•
The accessories must be inserted correctly in the accessory
guiding rails of the diffuser / intensifier.
•
Attach an appropriate rated safety cable to the safety hole
in the accessory. Affix the safety cable to the rigging struc-
ture or the safety loop attachment (C) of the SkyPanel yoke.
•
Do not store the remote control in the trough when using the
fixture over head.
•
The four eyelets (5) can be used to hang the fixture horizon-
tally. Attach an appropriately rated safety cable to each eye-
let. Four safety cables are required in total. Secure the
opposite end of each safety cable with one appropriately
rated shackle to form a single hoist point.
•
Tripods must be set up in a stable way and must be rated to
carry the required load. Please observe the weight of the
accessories and the cables. Please refer also to the leaflet
„Operating your ARRI Lampheads Safely" L5.40731.E.
Basic Functions
MOUNTING
The SkyPanel must be mounted on its yoke (2) in a standing
position or a hanging position. Always insert the 28 mm spigot
(1) into the bushing of a suitable stand or a suitable clamping
system and fix and secure the spigot afterwards.
PAN AND TILT
•
Swivel the SkyPanel after loosening the screw of the stand
or the clamping system. The tilt angle can be adjusted by re-
leasing both tilt locks (3). After the adjustment of the pan an-
gle and the tilt angle, the screws respectively clamps must
be fastened again.
TO ADJUST THE BEAM ANGLE
•
The beam angle can be adjusted by using different diffuser
panels (6) or the intensifier.
3
Publicité
