Troubleshooting - Amana W10577942B Guide D'utilisation

TROUBLESHOOTING

First try the solutions suggested here or visit our website at www.amana.com/help
If you experience
Error Code Appears in Display
Once any possible issues are corrected, touch POWER once to clear the code. Reselect and restart the cycle.
"Sd" (Excess suds)
appears in display
F 8 followed by E 1 (water
supply error) appears in
display
F 9 followed by E 1 (drain
pump system error)
appears in display
F 5 followed by E 2 (door
will not lock) appears in
display
F 7 followed by E 1 (motor
drive error) appears in
display
"rL"
(remove load)
appears in display
Washer making error
beeps
Washer beeps when
HOLD TO START is
touched
F # E #
code other than
as described above
appears in display
"nt" (interrupted)
appears in display
Clean Washer LED
flashing at end of wash
cycle
for assistance and to possibly avoid a service call.
Possible Causes
Excessive suds in washer. Washer is
running a suds reduction routine.
Check for proper water supply.
Check plumbing for correct drain
hose installation. Drain hose extends
into standpipe farther than 4
1
(114 mm).
Not using HE detergent or using too
much HE detergent.
Washer door not locking.
Motor is having difficulty turning
the drum.
Load detected in drum during Clean
Washer with affresh cycle.
®
Door has not been opened and closed
for at least 3 cycles.
Door not closed.
System error code.
The cycle was paused or cancelled.
The washer has run 30 wash cycles
and is indicating a reminder to run the
Clean Washer cycle.
Allow the washer to continue. Use only HE detergent.
Always measure detergent, and base detergent quantity on
load size. Follow detergent manufacturer's instructions.
Both hoses must be attached and have water flowing to the
inlet valve.
Both hot and cold water faucets must be on.
Inlet valve screens on washer may be clogged.
Remove any kinks in the inlet hose.
Touch POWER once to clear the code. Then touch POWER
again to restart washer. If code appears again, call for service.
Check drain hose for proper installation.
Make sure the drain hose is not kinked, pinched, or blocked.
⁄ "
2
Remove any clogs from drain hose.
Use drain hose form and securely attach to drainpipe or tub.
Lower drain hose if the end is higher than 96" (2.4 m) above
the floor.
Use only HE detergent. Always measure detergent and follow
manufacturer's directions based on load size and soil level.
Touch POWER to cancel the cycle. Make sure the door is
closed completely and latching. Check for items in the washer
drum that may be keeping the door from closing completely.
Washer is tightly packed. Remove some items. See "Cycle
Guide" for load size recommendations. Make sure that all
shipping materials have been removed. See the Installation
Instructions.
Remove items from washer drum and restart Clean Washer
with affresh
®
This code may appear when the washer is first turned on.
Open and close the door to clear the display.
Close the door completely.
Touch POWER once to clear the code. Then touch POWER
again to restart washer. If code appears again, call for service.
The washer can take 20 to 30 minutes to stop spinning and
drain and will display this error code during that time. Touch
POWER once to clear the code. Then touch POWER again to
restart washer.
Run the Clean Washer cycle. If the Clean Washer cycle is not
turned on, the LED will stop flashing at the end of a wash cycle
after running 3 more regular wash cycles. After 30 more wash
cycles are completed, the Clean Washer LED will again flash at
the end of a wash cycle as a reminder.
Solution
cycle.
13