Hoover FREESPACE EVO FV70 Manuel D'utilisation page 4

GETTING TO kNOw yOUR ClEANER
A. Cleaner main body
B. On/Off & Variable Power Control Roller
C. Bag Check Indicator
D. Bag Door Release Buttons
E. Hose Latch
F. Handle
G. Telescopic Tube
H. Telescopic Tube Adjusters
I. Hose
J. Handle Hook
K. Telescopic Tube Parking Hook
L. Hose Release Buttons
M. Carpet and Floor nozzle(GP)**
M1. Carpet Nozzle (CA)**
M2. Hard Floor Nozzle (HF)**
N. Floor Type selector
O. Crevice Tool
P. Dusting Brush
Q. Nozzle Parking slot
R. Telescopic Tube Parking slot
s. Parquet Nozzle*
T. Pet Hair Remover Mini Turbo Nozzle*
U. Allergen Remover Mini Turbo Nozzle*
V. Grand Turbo Nozzle*
ASSEmBlING yOUR ClEANER
Remove all components from the packaging.
1. Connect the hose to the cleaner main body, ensuring it clips and locks into position. To
release: simply press the two buttons on the hose end and pull. [2]
2. Connect the handle to the tube upper end [3].
3. Connect the carpet and floor nozzle to the tube lower end. [4]
*Certain models Only ** Certain models only, nozzles may vary according to model
USING yOUR ClEANER
1. Extract power cord and plug it into the power supply. [5] Do not pull the cord beyond the
red marker.
2. Adjust the telescopic tube to the desired height by moving the telescopic tube adjuster up
and raise or lower the handle to the most comfortable cleaning position. [6]
3. Carpet & Floor Nozzle. Press the floor type selector on the nozzle [7] to select the ideal
cleaning mode for the floor type.
Hard Floor – Brushes are lowered to protect the floor.
Carpet – Brushes are raised for the deepest clean.
4. switch the cleaner on by rotating the On/Off Variable Power Control Roller clockwise on the
rear of the cleaner main body. [8]
5. Adjust the power level by rotating the On/Off Variable Power Control Roller to the desired
level. [8]
6. switch off at the end of use by rotating the On/Off Variable Power Control Roller anti-
clockwise to the end. [8] Unplug and gently pull the power cord out of the cleaner and the
cord will begin to automatically retract back into the cleaner. [9]
7. Parking and storage - The flexible hose and tube can be parked for temporary storage while
in use [10] or in the Nanopack storage position when not in use: Retract the telescopic tube
to its storage length [6]. Remove the nozzle from the end of the telescopic tube [11] and
remove the hose handle from the telescopic tube [12]. Lift the hose latch at the rear of the
cleaner [13] and wrap the flexible hose around the product [14]. Park the hose handle on
the product [15]. Assemble the nozzle into the parking slot underneath the product [16].
Assemble the telescopic tube into the remaining parking slot underneath the product [17].
ClEANER mAINTENANCE
Replacing The Dust Bag
If the bag check indicator [1C] is red please check and, if necessary, replace the bag.
1. Remove the hose from the cleaner [2].
2. Press the Bag Door Release buttons and remove bag door [18].
3. Pull the bag collar to remove the dust bag [19] and carefully dispose the bag into a bin.
4. Fit a new bag into the cleaner by inserting the bag collar into the bag holder [19].
ImPORTANT: The hose must be removed before removing or replacing the dust bag.
REmEmBER: The bag check indicator may be red if an obstruction has occurred. In this case
refer to 'Removing A Blockage From the system' .
Cleaning the Filters
To maintain optimum performance of your cleaner, please wash the pre-motor filter and exhaust
filter after each 5 bag changes.
To remove the pre-motor filter:
1. Open the bag door and remove the dust bag from the cleaner (see "Replacing The Dust
Bag").
2. Press the latch at the top of the pre-motor filter frame to unlock it from the cleaner. Tilt and
remove the filter from the cleaner [20].
2
GB