Milwaukee HEAVY DUTY M18 SMS216 Notice Originale page 29

Technical Data
Mitresaw
Production code
No-load speed
Battery voltage
Saw blade dia. x hole dia
Saw blade thickness
Cutting width max.
Mitre 0°/ Bevel 0°
Mitre 45°/ Bevel 0°
Mitre 0°/ Bevel 45°
Mitre 45°/ Bevel 45°
Min. workpiece dimensions
Recommended Ambient Operating Temperature
Recommended battery types
Recommended charger
GB
Weight according EPTA-Procedure 01/2014
Noise information
Measured values determined according to EN 62841. Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A))
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!
WARNING:
The noise emission level given in this information sheet has been
measured in accordance with a standardized test given in EN 62841
and may be used to compare one tool with another. It may be used
for a preliminary assessment of exposure.
The declared noise emission level represents the main applications
of the tool. However if the tool is used for different applications,
with different accessories or poorly maintained, noise emission may
differ. This may significantly increase the exposure level over the
total working period.
An estimation of the level of exposure to noise should also take
into account the times when the tool is switched off or when it is
running but not actually doing the job. This may significantly reduce
the exposure level over the total working period..
Identify additional safety measures to protect the operator from the
effects of noise such as: maintain the tool and the accessories and
organization of work patterns.
Wear ear protectors. Exposure to noise can cause hearing loss.
WARNING Read all safety warnings, instructions,
illustrations and specifications provided with this power
tool. Failure to follow all instructions listed below may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS FOR MITRE SAWS
a) Mitre saws are intended to cut wood or wood-like
products, they cannot be used with abrasive cut-off wheels
for cutting ferrous material such as bars, rods, studs, etc.
Abrasive dust causes moving parts such as the lower guard to jam.
Sparks from abrasive cutting will burn the lower guard, the kerf
insert and other plastic parts.
English
26 26
b) Use clamps to support the workpiece whenever possible.
If supporting the workpiece by hand, you must always
keep your hand at least 100 mm from either side of the saw
blade. Do not use this saw to cut pieces that are too small
to be securely clamped or held by hand. If your hand is placed
too close to the saw blade, there is an increased risk of injury from
blade contact.
c) The workpiece must be stationary and clamped or held
against both the fence and the table. Do not feed the
workpiece into the blade or cut "freehand" in any way.
Unrestrained or moving workpieces could be thrown at high speeds,
causing injury.
d) Push the saw through the workpiece. Do not pull the saw
through the workpiece. To make a cut, raise the saw head
and pull it out over the workpiece without cutting, start the
motor, press the saw head down and push the saw through
the workpiece. Cutting on the pull stroke is likely to cause the
saw blade to climb on top of the workpiece and violently throw the
blade assembly towards the operator.
e) Never cross your hand over the intended line of cutting
either in front or behind the saw blade. Supporting the
workpiece "cross handed" i.e. holding the workpiece to the right of
the saw blade with your left hand or vice versa is very dangerous.
f) Do not reach behind the fence with either hand closer
than 100 mm from either side of the saw blade, to remove
wood scraps, or for any other reason while the blade is
spinning. The proximity of the spinning saw blade to your hand
may not be obvious and you may be seriously injured.
M18 SMS216
4745 85 03...
... 000001-999999
2700 min
-1
18V
216 x 30 mm
1,5 mm
60 x 270 mm
60 x 190 mm
48 x 270 mm
48 x 190 mm
130 x 35 x 2 mm
-5°C - +40°C
M18B..., M18HB...
M12-18..., M1418 C6
14,5 kg
91,8 dB (A)
104,8 dB (A)