F.F. Group CID 12V/80 PLUS Notice Originale page 9

CHD 12V PLUS
fied on the rating plate of the charger unit. Plug your
mains plug into the power source. The green LED
indicator 11.2 will blink indicating stand-by mode.
Insert battery pack into battery compartment of the
charger. The red LED indicator will light solid. This
indicates that the battery pack is being fast charged
automatically. When the battery pack is fully charged,
the red LED indicator will turn off and the green LED
will illuminate solid. Remove the battery pack from
the charger and unplug.
IMPORTANT CHARGING NOTES: Longest life and
best performance can be obtained if the battery pack
is charged when the surrounding air temperature is
between 18°C and 24°C. DO NOT charge battery pack
in an air temperature below 4.5°C, or above 40.5°C.
This is important and will prevent serious damage
to the battery pack. The charger is designed to fast
charge the battery pack between 0°C and 45°C. If the
battery pack, when inserted, is too cold or too hot,
the charger will not charge. The green LED and the
red LED will blink alternatively and continuously to
indicate this situation. Once the air temperature is
within tolerance, the fast charging will begin.
CHARGER LIGHT INDICATOR
LED INDICATOR
Green Red
Blinking light No Light
No Light Solid Light
Solid Light No light
Blinking light Blinking light
No light Blinking light
DUST AND SWARF
A correctly fitted dust mask, suitable for the ac-
tivity and in accordance to the relevant standard
must be worn. Swarf produced by metal drilling is
extremely sharp. Take precautions when clearing
swarf. The burr left on the hole is also sharp and
should be removed with a suitable tool. Always
wear safety goggles.
WARNING: Drill bit will be hot after use.
INSTALLING AND REMOVING BITS
The drill is fitted with a keyless chuck, this means
that a chuck key is not required to secure the drill
or screwdriver bit.
i. Place the drill bit shoulder into the chuck as far
as it will go.
ii. Tighten the chuck firmly.
LED WORK LIGHT
FORWARD/REVERSE SELECTOR
TRIGGER
SITUATION
Stand by
Charging
Charging is
complete
TORQUE SELECTION CONTROL
Battery pack is
too hot or cold
(charging will begin
automatically when
battery reaches cor-
rect charging tem-
perature)
Damaged or
faulty battery
pack
TWO SPEED GEAR BOX
HOLDING THE DRILL (image 1 & 2)
Note: Short screwdriver bits need only be insert-
ed to the depth of the hexagon shank before
tightening chuck by hand.
To aid drilling and screwdriving in confined, inade-
quately lit spaces, the LED work light (7) automati-
cally illuminates when the trigger is activated.
The switch determines the direction of rotation
of the chuck, i.e. clockwise or anticlockwise.
i. Stop the drill and push switch (2) to the left
or right. NOTE: When the direction switch is
pushed to the left, the chuck will rotate clock-
wise. Before operation, check that the switch
is set in the required position. Do not change
the direction of rotation until the chuck
comes to a complete stop.
ii. When the drill is not in use move the direction
switch to the neutral position (the middle set-
ting) to lock the trigger out.
When the trigger is depressed, the chuck will ro-
tate (provided the direction switch is set in the
forward or reverse position). This trigger switch
is electronic which enables the user to vary the
speed continuously. The speed varies according
to how far the trigger switch is depressed. The
further it is depressed, the faster the chuck will
rotate. The lighter it is depressed, the slower it
will rotate.
By turning the collar (4) it is possible to adjust the
amount of torque. Settings 1-21 provide a facil-
ity for setting the torque to the required level.
For example, this means that repetitive driving
of screws of the same size will be driven into the
material to the same torque, thus giving the same
fixing strength, or in the case of countersunk
screws, these will all be driven to the same depth
in the material. The torque control prevents the
heads of small diameter screws being twisted off
when correctly set. By turning the collar (5) it is
possible to switch between rotary drilling, per-
cussion drilling and screwdriving functions. Set
the "twist drill" setting
screwdriving, in the "hammer drill" setting
the percussion feature will come into action. This
is intented for drilling into masonry, etc. Turn the
collar to the setting to use the drill for screw-
driving.
Select a low gear (1) (slower rotational speed and
higher torque) for screwdriving.
Use a high gear (2) (faster rotational speed and
lower torque) for drilling holes.
The drill casing is designed to be held comfort-
ably in two ways,
1. By the handle.
English | 9
, for rotary drilling/
,
www.ffgroup-tools.com