Publicité
Les langues disponibles
Les langues disponibles
BeFore FIrst use
•
It is normal for small amount of smoke to
be produced the first time, this will quickly
disappear.
•
When using the steam function for the first
time, do not direct the steam towards the
laundry, as there could be debris from the
steam vents.
FIX tHe locKInG stAnD on tHe
IronInG BoArD
•
Pull out the bracket from the locking stand
and fix it on the ironing board.
suPPlY oF electrIcItY
•
Set the iron on the stand and plug in.
FIllInG WItH WAter
•
Make sure that both the Steam Control
turning Knob and Temperature Control
Dial are in "OFF" position.
•
Set the 3-Position switch to 1 position and
remove the cordless iron from the stand.
•
Hold the iron upright so that the water-
filling inlet is in a horizontal position.
•
Fill with water through Water Filling Inlet
until the water reach the "MAX" mark
indicated on the side of the iron, and
never fill above this mark.
teMPerAture control settInG
GArMent
FABrIc
tHerMostAt
lABel
tYPe
reGulAtIon
silk
low temperature
l
wool
medium
ll
temperature
Cotton - linen
high temperature
lll
•
Always check first to see whether a label
with ironing instructions is attached to
the article to be ironed. Follow these
instruction in all cases.
•
First you should sort the laundry: Wool
with wool, Cotton with cotton etc. Start
ironing the fabrics requiring the lowest
temperature and progress to the higher
ones because the iron heats up quicker
than it cools down.
•
If the fabric consist of various kinds of
fibres (e.g. cotton with polyester) you
must always select the lowest ironing
temperature of the composition of those
fibres.
steAM IronInG
•
Place the iron in a vertical position and
set the temperature control dial at the
minimum/low heat setting.
•
Insert the plug into the socket, and then
turn the temperature control dial to the
"high heat" marking. The pilot light will
come on, indicating that the iron is heating
up.
•
The correct temperature will be reached
when the pilot light has turned off. The
pilot light will be on and off from time
to time indicating that the selected
temperature is being maintained.
•
Turn the steam knob to the required
position
•
Steam is produced as soon as the iron in
held horizontally.
sPrAYInG
•
Press the spray button to spray water on
clothes, as often as required.
Note: When using the water spray function,
ensure that there is enough water in the
water tank, and you may have to pump the
spray button serval times at first time you
use the iron in order to start the spraying
function.
selectInG sHot-steAM AnD
steAM WHen IronInG VertIcAllY
Press the shot-steam button to generate a
powerful burst of steam that can penetrate
the fabrics and smooth the most difficult and
tough creases. Wait for a few seconds before
pressing again.
By pressing the shot-steam button at
intervals you can also iron vertically (curtains,
hung garments, etc.)
Warning: the shot-steam function can only
be used at high temperatures. Stop the
emission when the plate temperature control
light comes on, than start ironing again only
after the light has gone off.
DrY IronInG
To iron without steam, follow the instructions
in section "steam ironing", leaving the steam
selector on position "OFF".
4
corDeD IronInG
1. Set the 3-position switch to 3 position
2. Take the iron (with power unit)from the
stand for IRONING.
3. Replace the iron (with power unit )on the
stand after used and set the 3-position
switch to 2 position.
corDless IronInG
1. Set the 3-position switch to 1 position.
2. Take the iron(without power unit)from the
stand.
3. Always replace the iron on the stand
during ironing intervals.
4. When the iron is correctly placed on the
stand, the pilot light (K) will illuminate.
5. If the soleplate needs heating up to the
set temperature,the indicator lamp (K) will
also be activated.As soon as the soleplate
has regained the set temperature,this light
will cut out.
6. We advise you to use the iron in the
corded position if you intend to steam
iron for a length of time and when you
apply numerous shots of steam,as this
can cause the soleplate to cool down
considerably.
AntI-cAlc sYsteM
A special resin filter inside the water reservoir
softens the water and prevents scale build-up
in the plate. The resin filter is permanent and
does not need replacing.
Please note:
Use tap water only. Distilled and/
demineralised water makes the "Zero-Calc"
anti-calc system ineffective by altering its
physicochemical characteristics.
Do not use chemical additives, scented
substances or decalcifiers.
AntI-DrIP:
This iron is equipped with a drip stop
function: the iron automatically stops
steaming when the temperature is too low
to prevent water from dripping out of the
soleplate.
With the anti-dripping system, you can
perfectly iron even the most delicate fabrics.
HoW to cleAn AnD store
•
After using, lift the iron with the filling hole
downwards to empty the remaining water
from the Water tank.
•
Insert the plug into the socket, and set the
Temperature Control Dial to "MAX" for 1-2
minutes to evaporate the remaining water,
and then unplug the iron and let it cool
down .
•
The iron should be fixed in position 2
(storage position) after using.
sPecIFIcAtIons
Power: 220-240V • 50/60Hz • 2200W
environment friendly disposal
You can help protect the environment!
Please remember to respect the local
regulations: hand in the non-working
electrical equipments to an appropriate waste
disposal center.
5
Publicité
