Hitachi WF 4H2 Mode D'emploi page 7

GENERAL OPERATIONAL PRECAUTIONS
1. Operate the power tool safety for correct uses.
Do not use the power tool for uses other than those
specifi ed in this instructions.
2. For safe operation handle the power tool correctly.
Please follow the instructions given in this instruction
manual and correctly handle this tool so as to ensure
safe operation. Never let the tool be use by children or
people who do not know enough to be able to handle it
correctly, or let it be used by people who cannot operate
it correctly.
3. Confi rm the safety of the workshop.
Keep unauthorized people away from the workshop.
Especially children should be kept away.
4. The right parts in the right places.
Do not remove any of the covers or screws. Keep them in
place as they have their functions.
Moreover, because it would be dangerous, never
make modifi cations to the tool or use it after making
modifi cations.
5. Check the tool before using it.
Before using the tool, always check that no parts of it are
broken, that all screws are completely tight, and that no
parts are missing or rusty.
6. Excessive work could cause accidents.
Do not make tools and accessories work beyond their
abilities. Excessive work not only damages the power
tool but also is dangerous in itself.
7. Stop operation immediately if abnormalities are
noticed.
Stop operation if you notice abnormalities, or if the
power tool does not work properly; have the power tool
inspected and serviced.
8. Look after the power tool carefully.
If you drop or knock the power tool against things, the
outer frame may be deformed and cracks or other kinds
of damage may occur, so please handle it with suffi cient
care. Also, do not scratch or engrave signs on the power
tool. Owing to high pressure air inside the tool, cracks in
the surface are dangerous.
Never use the power tool if a crack develops or if air is
escaping from a crack.
9. Take good care for a long life.
Always take good care of the power tool and keep it
clean.
10. Inspection at regular intervals is essential for safety.
Inspect the power tool at regular intervals so that the
power tool can be operated safety and effi ciently at all
times.
11. Consult an authorized service center if repair or
parts replacement is necessary.
Ensure that the power tool is serviced by authorized
service center only, and that only genuine replacement
parts are used.
12. Keep the power tool in a proper place.
When not in use, the power tool should be kept in a dry
place out of the reach of children. Put into the body about
2cc oil through the hose joint to protect the tool from rust.
13. The exploded assembly drawing on this handling
instructions should be used only for authorized
service center.
(Original instructions)
PRECAUTIONS ON USING AUTOMATIC SCREW
DRIVER
1. Safe operation through correct usage
This tool was designed for driving screws into wood and
similar materials. Use it for its intended purpose only.
2. Make sure air pressure is within the rated range of
air pressure.
Please make sure that the air pressure is within a range
of 18 bar – 23 bar, and that the air which is used is clean
and dry. If the air pressure is greater than 23 bar, the
life of the power tool will be shortened and dangerous
conditions could develop. Tools shall not be connected
to pressure which potentially exceeds 26 bar .
3. Never operate the equipment with high-pressure
gases other than compressed air.
Never use carbon dioxide, oxygen or another gas from
pressurized containers under any circumstances.
4. Be careful of ignition and explosions.
Since sparks may fl y during driving screw, it is dangerous
to use this tool near lacquer, paint, benzine, thinner,
gasoline, gas, adhesives and similar infl ammable
substances as they may ignite or explode. Under no
circumstances should this tool therefore be used in the
vicinity of such infl ammable material.
5. Always wear eye protection (protective goggles).
When operating the power tool, always wear eye
protection, and ensure that surrounding people wear eye
protection too.
The possibility of fragments of the plastic linking the
screws or screws that were not properly hit entering the
eye is a threat to sight. Eye protection can be bought at
any hardware store. Always wear eye protection while
operating this tool. Use either eye protection or a wide
vision mask over prescription glasses.
Employers should always enforce the use of eye
protection equipment.
6. Protect your ears and head.
When engaged in driving screw work please wear
ear muffl ers and head protection. Also, depending on
condition, ensure that surrounding people also wear ear
muffl ers and head protection.
7. Pay attention to those working close to you.
It would be very dangerous if screws that were not
properly driven in should hit other people. Therefore,
always pay attention to the safety of the people around
you when using this tool. Always make sure that nobody's
body, hands or feet are close to the screw outlet.
8. Never point the screw outlet towards people.
Always assume the tool contains fasteners.
If the screw outlet is pointed towards people, serious
accidents may be caused if you mistakenly discharge
the tool. When connecting and disconnecting the hose,
during screw loading or similar operations, be sure the
screw outlet is not pointed towards anyone (including
yourself). Even when no screws are loaded at all, it
is dangerous to discharge the tool while pointing it at
someone, so never attempt to do so. No horseplay.
Respect the tool as a working implement.
9. Before using the power tool, check the push lever.
Before using the power tool make sure to check that the
push lever and valve operate properly. Without screws
loaded into the power tool, connect the hose and check
the following. If the sound of operation occurs this
indicates a fault, so in such a case do not use the power
tool until it has been inspected and repaired.
English
7