Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Alternate Parts
Your installation may require additional parts. If you are
interested in purchasing one of the items listed here, contact the
distributor where the washer was purchased.
If you have
Laundry tub or standpipe
taller than 96" (2.4 m)
Overhead sewer
Floor drain
Drain hose too short
Water faucets beyond
reach of fill hoses
Accessories
Enhance your washer with these premium accessories.
For more high-quality items or to order, call 1-800-901-2042, or
visit us at www.whirlpool.com/accessories. In Canada call:
1-800-807-6777 or visit us at www.whirlpoolparts.ca.
Part Number
Accessory
8212487RP
5 ft (1.5 m) nylon braided inlet hose
(2-pack)
8212526
Washer drip tray, fits under all
31682
All purpose appliance cleaner
1903WH
Laundry supply storage cart
Pedestal
You have the option of purchasing pedestals separately for this
washer. The pedestal will add to the total height of the washer.
Optional pedestal
Pedestal
Approximate
Height
height with washer
2
⁄
" (73 mm)
47.5" (1207 mm)
7
8
4
You will need to buy
Sump pump system (if not already
available)
Standard 20 gal. (76 L),
30" (762 mm) tall drain tub or utility
sink and sump pump (available
from local plumbing suppliers)
Siphon break, Part Number
285834; additional drain hose,
Part Number 8318155; and
connector kit, Part Number 285835
4 ft (1.2 m) drain hose extension
kit, Part Number 285863
2 longer water fill hoses:
6 ft (1.8 m) Part Number 76314
10 ft (3.0 m) Part Number 350008
Options
Color
Model
Number
White
WHP0400VW
Location Requirements
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer "walk."
Your washer can be installed under a custom counter, or in a
basement, laundry room, closet, or recessed area. See "Drain
System." Companion appliance location requirements should
also be considered. Proper installation is your responsibility.
You will need
A water heater set to deliver 120°F (49°C) water to the
■
washer.
A grounded electrical outlet located within 6 ft (1.8 m)
■
of where the power cord is attached to the back of the
washer. See "Electrical Requirements."
Hot and cold water faucets located within 4 ft (1.2 m) of
■
the hot and cold water fill valves, and water pressure of
20-100 psi (137.9-689.6 kPa).
A level floor with a maximum slope of 1" (25 mm) under
■
entire washer. Installing the washer on soft floor surfaces,
such as carpets or surfaces with foam backing, is not
recommended.
A sturdy and solid floor to support the washer with a total
■
weight (water and load) of 400 lbs (180 kg).
Do not operate your washer in temperatures below 32°F (0°C).
Some water can remain in the washer and can cause damage
in low temperatures.
Installation clearances
The location must be large enough to allow the washer
■
door to be fully opened.
Additional spacing should be considered for ease of
■
installation and servicing. The door opens more than 90°,
and it is not reversible.
Additional clearances might be required for wall, door, and
■
floor moldings.
Additional spacing of 1" (25 mm) on all sides of the washer
■
is recommended to reduce noise transfer.
Companion appliance spacing should also be considered.
■
Washer Dimensions
1
50
/
"
2
(1282 mm)
Door is not reversible.
27"
(686 mm)
5
44
/
8
(1134 mm)
13
37
/
"
16
(961 mm)
13
28
"
/
16
(732 mm)
"
Publicité
Table des Matières
