Whirlpool CHW8990XW0 Instructions Pour L'installation page 12

CODE
Options to use if SPECIAL PRICING is selected (cont.):
SPECIAL PRICE STOP HOUR
8. 00
NOTE: Uses military time or 24 hr. clock
8. 00 This is the stop hour; 0-23 hours. Select STOP
HOUR by pressing the HOT button.
Press the WARM button once to advance
g
to next code.
SPECIAL PRICE DAY
9. 10
9. 10 This represents the day of the week and whether
special pricing is selected for that day. A number
followed by '0' indicates no selection that
particular day (9.10). A number followed by an 'S'
indicates selected for that day (9.1S). To change
the value of '0' and 'S', use the COLD button.
Days of the week (1-7) are selected by pressing
the HOT button.
When exiting set-up code '9', the display must
show current day of week:
DISPLAY DAY OF WEEK
10 Day 1 = Sunday
20 Day 2 = Monday
30 Day 3 = Tuesday
40 Day 4 = Wednesday
50 Day 5 = Thursday
60 Day 6 = Friday
70 Day 7 = Satday
g Press the WARM button once to advance to next
code.
A. 00 VAULT VIEWING OPTION
This option is either SELECTED = 'ON' or NOT
SELECTED = 'OFF'.
A. 00 NOT SELECTED = 'OFF'.
A. SC SELECTED = 'ON'. Press the COLD button once
for this selection. When selected, the money and/
or cycle counts will be viewable (if counting is
selected) when the coin box is removed.
Press the WARM button once to advance to next
g
code.
b. 05 VALUE OF COIN 1
b. 05 This represents the value of coin 1 in number
of nickels: 05 = $0.25; may adjust from 1-199.
Change this value by pressing the Hot button.
When d.CS is set to d.00, this value represents
total vend price in nickels; b.35=$1.75. This total
will be shown in the display as the vend price,
may adjust from 1-199. Change this value by
pressing the HOT button.
g Press the WARM button once to advance
to next code.
VALUE OF COIN 2
C. 20
C. 20 This represents the value of coin 2 in number
of nickels; 20 = $1.00.
By pressing the HOT button you have the option
of 1-199 nickels.
g Press the WARM button once to advance
to next code.
12
EXPLANATION
CODE (selected)
1S
2S
3S
4S
5S
6S
7S
CODE
d. 00 COIN SLIDE OPTION
This option is either SELECTED = 'ON' or NOT
SELECTED = 'OFF'.
d. 00 NOT SELECTED = 'OFF'. Used when washer
is set-up as OPL, or with a coin drop or a card
reader.
d. CS SELECTED = 'ON'. When coin slide mode
is SELECTED = 'ON', set 'b.xx' equal to
value of vend price in nickels. Set set-up code
6 xx (regular cycle price) and set-up code 3.xx
(special cycle price) to number of slide pushes.
NOTE: If washer is set up as 'CS' and a coin
drop is installed, it will not register coins.
Press the WARM button once to advance
g
to next code.
ADD COINS OPTION
E. 00
This option is either SELECTED = 'ON' or NOT
SELECTED = 'OFF'. This option causes the
customer display to show the number of coins
(coin 1) to enter, rather than the dollars-and-
cents amount.
E. 00 NOT SELECTED = 'OFF'.
E. AC SELECTED = 'ON'. Press the COLD button
3 consecutive times for this selection.
Press the WARM button once to advance
g
to next code.
ENHANCED PRICING OPTION
F. 00
F. 00 NOT SELECTED = 'OFF'.
F. CP Cycle-Based pricing enabled. This option allows
configuration of different prices for cold, warm,
and hot water selections.
Press the WARM button once to advance
g
to next code.
COIN/DEBIT OPTION
J. Cd
J. Cd Both coin and debit selected. Press the COLD
button 3 consecutive times to change this
selection.
J. C_ Coins selected, debit disabled. Press the COLD
button 3 consecutive times to change this
selection.
J. _d Debit Card selected, coins disabled. Press the
COLD button 3 consecutive times to change this
selection.
J. Ed Enhanced debit is self-selected when a
Generation 2 card reader is installed in the
washer. The Ed option cannot be manually
selected or deselected.
g Press the WARM button once to advance
to next code.
L. 00 PRICE SUPPRESSION OPTION
This option causes the customer display to
show 'ADD' or 'AVAILABLE' rather than the
amount of money to add. (Used mainly in debit
installations.)
L. 00 NOT SELECTED = 'OFF'.
L. PS PS SELECTED = 'ON'. Press the COLD button
once for this selection.
g Press the WARM button once to advance
to next code.
EXPLANATION