Specifications; Location Requirements - Whirlpool 3LWTW4705FW Instructions Pour L'installation

Masquer les pouces Voir aussi pour 3LWTW4705FW:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 12

Specifications

These units are sold in multiple regions with different
requirements for measuring capacity. Below are a few
of the valid forms of measure posted on this product:
Dry Linen Capacity: A weight measure that reflects a
maximum load size that can be loaded into the washer.
GULF (GSO) Capacity: A capacity measure that represents
the capacity at which performance testing was completed.
GULF (GSO) Water Consumption: Water consumption which
the manufacturer declares will be used in a specific cycle.
IMPORTANT:
This appliance is intended to be used in
household and similar applications such as:
• staff kitchen areas in shops, offices, and other working
environments;
• farm houses;
• by clients in hotels, motels, and other residential-type
environments;
• bed and breakfast-type environments;
• areas for communal use in blocks of flats or in launderettes.
Dry Linen Capacity
15 kg (33 lb)
IEC Capacity
15 kg (33 lb)
GULF (GSO) Capacity
15 kg (33 lb)
GULF (GSO) Water
Consumption
153 litres
Inlet Valve Water Pressure Specifications
Max. inlet
Min. inlet
water
water
pressure
pressure
862 kPa
55 kPa
NOTE: Sound Pressure Level, Lpa: 58 dBA (uncertainty,
Kpa: +/–10 dBA).
4
GULF
GULF
(GSO)
(GSO)
Max. inlet
Min. inlet
water
water
pressure
pressure
690 kPa
138 kPa

Location Requirements

Select proper location for your washer to improve performance
and minimize noise and possible "washer walk". Install your
washer in a basement, laundry room, closet, or recessed area.
1067 mm
(42")
You will need:
A water heater set to 49°C (120°F).
n
An earthed electrical outlet located within 1.2 m (4 ft) of power
n
cord on back of washer.
Hot and cold water faucets located within 0.9 m (3 ft) of hot
n
and cold water fill valves on washer, and water pressure
of 138–690 kPa (20–100 psi).
A level floor with maximum slope of 25 mm (1") under entire
n
washer. Installing on carpet is not recommended.
Floor must support washer's total weight (with water and load)
n
of 143 kgs (315 lbs).
IMPORTANT: Do not install, store, or operate washer where it
will be exposed to weather or in temperatures below 0°C (32°F).
Water remaining in washer after use may cause damage in low
temperatures. See "Washer Care" in your Use and Care Guide
for winterizing information. Proper installation is your responsibility.
Recessed area or closet installation
356 mm
(14" max.)
126 mm
(5")
25 mm
(1")
Dimensions show recommended spacing allowed, except for closet
door ventilation openings, which are the minimum required. This washer
has been tested for installation with spacing of 0 mm (0") clearance on
the sides. Consider allowing more space for ease of installation and
servicing, and spacing for companion appliances and clearances for
walls, doors, and floor moldings. Add spacing of 25 mm (1") on all sides
of washer to reduce noise transfer. If a closet door or louvered door is
installed, top and bottom air openings in door are required.
IMPORTANT: Washers that feature ventilation openings in the base
of the unit must not be obstructed by carpet.
699 mm
686 mm
(27
")
(27")
1
2
76 mm
(3")
310 cm
(48 in.
432 mm
(17")
155 cm
(24 in.
25 mm
76 mm
(1")
(3")
2
)
2
2
)
2

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

3lwtw4815fw3lwtw4815f

Table des Matières