Télécharger Imprimer la page

EINHELL PROFI Silver Line PS-SB 650E Mode D'emploi page 12

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 15
Anleitung PS-SB 650 E_SPK1
GB
3. CONTROL ELEMENTS (Figure 1)
1. Keyless chuck
2. Selector switch (drill/hammer drill)
3. Depth stop
4. Locking button
5. ON/OFF switch
6. Speed setting ring
7. Clockwise/Counter-clockwise selector switch
8. Additional handle
4. TECHNICAL DATA
Power input:
Rated voltage:
Rated frequency:
Drill bit diameter:
max. 13 mm
Idle speed n
:
0-2800 rpm
0
Maximum drilling diameter
- Wood
- Concrete
- Steel
Weight (excluding accessories):
Protection class:
Noise and vibration
Permanent noise level LpA:
93.3 dB(A)
LWA peak noise level:
104.3 dB(A)
Hand-arm vibration: avhw:
5. PREPARATION
5.1 Additional handle (Figure 2)
The additional handle (8) enables you to achieve
better stability whilst using the hammer drill. Do
not use the tool without the additional handle (8).
Undo the handle. Thread the hammer drill's
chuck (1) through the collar in the additional
handle (8). The additional handle (8) is suitable
for both left-handed and right-handed users.
Position the handle (8) on the left or right side of
the hammer drill. Turn the handle (8) into the
best position for you.
Tighten the handle (8). Check that the handle (8)
is secure.
In addition you can adjust the additional handle
to suit your working position. You can do so by
pulling the additional handle downwards and then
turning the handle into the required position.
12
18.08.2005
13:04 Uhr
5.2 Depth stop (Figure 2)
The depth stop (3) is a practical aid to enable you
to drill several holes of the same depth.
Drill a hole of the required depth. Pull the power
plug.
Undo the additional handle (8). Insert the depth
stop (3) into the hole at the top end of the additio-
nal handle (8).
Adjust the depth stop (3) to the required depth:
Insert the drill bit into the hole. Now adjust the
depth stop (3) so that its tip touches the edge of
the workpiece. Tighten the handle (8) again.
After connecting the mains plug to the power
source you can then drill more holes of exactly
650 W
the same depth. As soon as the depth stop (3)
230 V~
touches the workpiece, the hole will have exactly
50 Hz
the same depth as the one you drilled previously.
5.3 Inserting the drill bit
Always pull the power plug before making adjust-
ments to the tool.
Ø 32 mm
This hammer drill is fitted with a keyless chuck
Ø 13 mm
(1).
Ø 10 mm
Open the chuck (1). The drill bit opening must be
2.1 kg
large enough to fit the drill bit into.
II / ®
Select a suitable drill bit or an accessory. Push
the tool as far as possible into the chuck opening.
Close the chuck (1). Check that the drill bit is
secure in the chuck (1).
Carry out several test drilling operations (see
14.1 m/s
2
next section). Wait until the drill bit has complete-
ly stopped. Only then should you pull out the
power plug and check again that the drill bit is
secure.
6. OPERATING THE HAMMER DRILL
6.1 Special instructions
The tool must neither be wet, nor be operated in
a damp environment.
Check the tool, mains plug and mains cable befo-
re use.
Connect the plug to a socket only if the tool is
switched off.
Always hold the tool in both hands.
Do not cover the ventilation slits. Keep them
clean at all times.
Keep the handles dry and free of oil and grease.
Ensure that there are not water pipes or power
cables behind the points you wish to drill.
Secure workpieces on a workbench or the like
wherever possible.
Seite 12

Publicité

loading

Ce manuel est également adapté pour:

44.710.72