The Lattoflex Remote Control - Lattoflex 292 Instructions De Montage Et D'utilisation

Installation instructions
Frame type and serial number
The name plate is located at the head end on
the left longitudinal beam below the raised
head.
Supplied accessories
Installation accessories: mattress holder (foot
end), 4 non-slip foils
Connection accessories: radio remote control
with batteries (3 x AAA), felt pocket, emergen-
cy lowering block, mains adapter, lead cable,
plug fuse
1
Placing in a bed
Please heed the necessary space for the
adjustable frame parts, e.g. in rooms with in-
clined roofs, superstructures over the bed or
padded head sections. An installation depth
of approx. 14 cm (floor clearance) is needed
in the substructure for the adjustment mecha-
nism and drive system.
Please always heed the spacing of the back
part with its motorised adjustment, to the
head part of the bed. There should be spa-
cing of at least 1.5 cm here when the bed is
laid flat. To rule out any unintentional slipping,
please screw the frame to the bed at the pre-
drilled points in the metal substructure.
2
Side support sections must not exceed 4 cm
in width (middle frame 8 cm). The motor
frame must always fit in the bed without any
tension. For beds with triangular supports
(leg length max. 15 cm), please use the „Ex-
tension elements" installation kit (available as
accessory). For a stable bed structure, we
always recommend a supporting point in the
middle of the bed for triangular supports.
Non-slip foil
Affix in the bed structure to the supporting
point of the frame. The foils prevent any noi-
se that could be caused by the frame slipping
in the bed structure.
3
Mattress holder
Attach the supplied holder at the foot end.
The plastic clamps are premounted.
Connection and commissioning
4
Please proceed as follows to commission
your motor frame:
Connect emergency lowering block to
1
jack 9 of the control. Connect up all other
accessory parts as appropriate.
Connect the mains adapter to the control
2
and clip the plug fuse in position.
Connect the motor frame to the mains.
3
Unpack the remote control and insert the
4
batteries
Remote control teach-in:
After inserting the batteries for the first time,
the language selection display appears.
Please select with the arrow buttons German,
English or French. Confirm by pressing
the middle button in the control cross. The
remote control is then automatically in the
menu to proceed with teach-in for a motor
frame.
1. Trigger the search mode by pressing the
middle button in the control cross.
2. Within 30 seconds, briefly press the but-
ton on the emergency lowering block.
3. The remote control shows „Teach-In Ok"
to confirm that the teach-in was success-
ful; the control in the motor frame beeps.
4. The display tells you to reset the unit:
5. To conclude the teach-in procedure, now
press button R until the picture of the mo-
tor frame appears on the display.
10

The Lattoflex remote control

Bi-directional radio connection
Your motor frame has been delivered with an
intelligent radio remote control. There is a
bi-directional i.e. two-sided radio connection
between the remote control and the control
unit in the motor frame. This offers you two
crucial advantages:
– The display only shows those motors and
accessories that are actually installed in
your frame. Components connected up
later on are automatically added to the
remote control menu after a correspond-
ing teach-in session.
– At all times, the display shows the exact
position of all adjustable parts and the
function status of all accessories.
5
Overview
1 - Display
2 - Control cross
3 - Menu change button
4 - Torch
5 - Reset
6 - Comfort buttons for favourite positions
7 - Battery compartment
Changing the batteries
Make sure that you have spare batteries rea-
dy as soon as there is only one red bar in the
battery display. You will need 3 batteries or 3
rechargeable batteries, size AAA. Simply push
open the cover of the battery compartment
on the back of the unit. Make sure you insert
the batteries with the positive and negative
ends pointing in the correct direction.
Motor frame control quick start
The remote control switches on automatically
when moved or when a button is pressed. If
no adjustment is made for 10 seconds or if
the remote control is not moved, it switches
to the sleep mode.
The 6 comfort buttons are preset on delivery.
This lets you quickly enjoy the full range of
functions. The presets can be changed at
any time and replaced by your own favourite
positions (see page 6, save settings). For
motor adjustment, press the corresponding
number button until the frame has reached its
end position.
Button 1 = reading and sitting position
Button 2 = raised legs
Button 3 = relax position
Button 4 = light on/off (stage 3 / 10 min),
optional
Button 5 = socket on/off, optional
Button 6 = electrical hot-water bottle on/off
(stage 3 / 15 min), optional
6
Menu overview
The Lattoflex remote control combines control
of the motor adjustments and all installed
Lattoflex components in one single control
unit. The various levels shown in Fig. 6 appear
on the remote control, depending on the
installed drives and function components.
Change between the levels:
by repeatedly pressing the menu change
button.
Return to the motor adjustment level:
by briefly pressing the R button (Reset).
The remote control switches on when moved
or when a button is pressed. The Lattoflex
logo always appears first, followed by the
motor adjustment.
Underbed lighting, socket receiver and hot-
water bottle are available as accessories. To
connect the hot water bottle with frame type
x92 and x93-U you have to replace the con-
trol and mains adapter. Please contact your
Lattoflex dealer.
11